Skip to main content

C.3.2 Pages for Operating a Physical Partition


C.3.2 Pages for Operating a Physical Partition
Table C-9 lists the functions provided to operate the power of physical partitions. Select [Menu] - [PPAR Operation] - [PPAR Power].
Table C-9  Physical Partition Power Operations
Item Overview Relevant Command
System power-on/off Specifies whether to power on or off the system (all physical partitions). showpparstatus(8)
poweron(8)
poweroff(8)
PPAR power-on/off or reset Performs the following operations for the specified PPAR:
- Power-on/off

- Forced power-off

- por: PPAR reset

- panic: Panic instruction to logical domains

- sir: Logical domain reset

- xir: CPU reset

- Break signal transmission
showpparstatus(8)
poweron(8)
poweroff(8)
reset(8)
sendbreak(8)
Table C-10 lists the function provided to set the physical partition operation mode. Select [Menu] - [PPAR Operation] - [PPAR Mode Configuration].
Table C-10  Physical Partition Operation Mode
Item Overview Relevant Command
PPAR mode display/setting Displays/Sets the following modes for the specified PPAR:
- Host ID

- Hardware diagnosis level

- Diagnosis message level

- Alive check function enabled/disabled

- Operation when Host Watchdog times out

- Break signal transmission suppression

- Auto boot function enabled/disabled for logical domains

- Low-power operation enabled/disabled

- I/O bus reconfiguration

- DR function currently enabled/disabled

- DR function enabled/disabled at next start

- PPAR Ethernet address (mac address)
showpparmode(8)
setpparmode(8)
Note - For support information on the Alive check function and DR function between the XSCF and Hypervisor, see the latest Product Notes for your server.
Table C-11 lists the functions provided to configure physical partitions. Select [Menu] - [PPAR Operation] - [PPAR Configuration].
Table C-11  Physical Partition Settings
Item Overview Relevant Command
PPAR configuration list display Displays the PCL of the specified PPAR system board (PSB). The function also displays/sets the configuration policy of the PPAR.
On the SPARC M12-1/M12-2/M10-1/M10-4, it can display information and set the configuration policy for PPAR-ID 00 only.
showpcl(8)
setpcl(8)
PCL setting Sets the PCL.
The function associates a PPAR LSB with a PSB and sets configuration information for an LSB.
The SPARC M12-1/M12-2/M10-1/M10-4 does not support this function.
showpcl(8)
setpcl(8)
PSB addition, deletion, or setting Instructs that the PSB configuration be changed as follows for a PPAR:
- Reserving or incorporating a PSB (BB) for a PPAR

- Releasing a PSB (BB) from a PPAR

- Moving a PSB (BB) from one PPAR to another PPAR

Perform the above operations by following the procedures described in the Fujitsu SPARC M12 and Fujitsu M10/SPARC M10 Domain Configuration Guide.
The SPARC M12-1/M12-2/M10-1/M10-4 does not support this function.
addboard(8)
deleteboard(8)
Table C-12 lists the function provided to set memory mirror mode. Select [Menu] - [PPAR Operation] - [PSB Configuration].
Table C-12  System Board Setting
Item Overview Relevant Command
Memory mirror information display/setting Displays/Sets memory mirror mode information for the CPUs on a system board (PSB). showfru(8)
setupfru(8)
Table C-13 lists the functions provided to set the configuration of a logical domain. Select [Menu] - [PPAR Operation] - [Domain Configuration].
Table C-13  Logical Domain Settings
Item Overview Relevant Command
Logical domain configuration information display Displays the logical domain configuration information for the specified PPAR. The configuration information has the following elements:
- Configuration name

- Number of constituent logical domains

- Date of configuration

The function also displays the configuration name of the logical domain currently in operation in the PPAR and the configuration name of the next logical domain to enter operation.
showdomainconfig(8)
Logical domain configuration setting Sets a logical domain configuration.
The function sets the configuration of the next logical domain scheduled to enter operation in the specified PPAR.
setdomainconfig(8)
Table C-14 lists the functions provided to overwrite the OpenBoot PROM environment variables for the control domain of a physical partition. Select [Menu] - [PPAR Operation] - [PPAR Parameter].
Note - For support information on [PPAR Parameter], see the latest Product Notes.
Table C-14  Setting OpenBoot PROM Environment Variables
Item Overview Relevant Command
Display/setting of PPAR OpenBoot PROM environment variables Displays/overwrites the following OpenBoot PROM environment variables overwrite settings for the specified PPAR.
- use-nvramrc

- security-mode

- bootscript
showpparparam(8)
setpparparam(8)
Table C-15 lists the functions provided to configure verified boot for each physical partition. Select [Menu] - [PPAR Operation] - [Verified Boot].
Table C-15  Configuring Verified Boot
Item Overview Relevant Command
Policy displaying/setting Displays/sets the boot or module policy for verified boot. showvbootconfig(8)
setvbootconfig(8)
System default certificate display Displays the X.509 public key certificate preinstalled on the system. showvbootcerts(8)
Registration/deletion/enabling/disabling of an X.509 public key certificate Registers/deletes a user-specified X.509 public key certificate.
Enables/disables/displays a user-specified X.509 public key certificate.
addvbootcerts(8)
deletevbootcerts(8)
showvbootconfig(8)
setvbootconfig(8)