Skip to main content
  1. Home >
  2. Products >
  3. Computing Products >
  4. Servers >
  5. Fujitsu SPARC servers >
  6. Downloads >
  7. User Manuals >
  8. Fujitsu M10-4/Fujitsu M10-4S/SPARC M10-4/SPARC M10-4S Service Manual >
  9. 5.8.1 Releasing of the SPARC M10-4S chassis (possible only in a system with a building block configuration)

Contents

  1. Preface
  2. Chapter 1 Before Starting Maintenance Work
    1.  1.1 Warning/Caution Indications
    2.  1.2 Warning Labels
    3.  1.3 Labels/Tags
    4.  1.4 Safety Precautions
    5.  1.5 Precautions on Static Electricity
    6.  1.6 Other Precautions
    7.  1.7 Emergency Power Off
  3. Chapter 2 Understanding the System Components
    1.  2.1 Identifying the Names and Locations of Components
    2. Click 2.2 Checking the Memory Configuration Rules
    3. Click 2.3 Confirming the Functions of the Operation Panel
    4. Click 2.4 Checking the LED Indications
    5. Click 2.5 Confirming the Types of Cable
  4. Chapter 3 Types of Maintenance
    1.  3.1 Types of Maintenance Supported in the SPARC M10-4/M10-4S
    2.  3.2 Active Maintenance
    3.  3.3 Inactive Maintenance
    4.  3.4 System-stopped Maintenance
  5. Chapter 4 Preparation and Precautions for Maintenance
    1. Click 4.1 Confirming the System Configuration
    2. Click 4.2 Troubleshooting
    3. Click 4.3 Maintenance Precautions
  6. Chapter 5 Preparations Required for Maintenance
    1.  5.1 Preparing Tools Required for Maintenance
    2.  5.2 Switching the Mode Switch to Service Mode
    3. Click 5.3 Checking the Operating Condition and Resource Usage Status
    4. Click 5.4 Preparations for Enabling Active Maintenance
    5.  5.5 Powering Off the Physical Partition Requiring Maintenance
    6. Click 5.6 Stopping the Entire System
    7.  5.7 Saving XSCF Setting Information
    8. Click 5.8 Releasing a SPARC M10-4/M10-4S FRU from the System with the replacefru Command
    9. Click 5.9 Accessing a FRU
  7. Chapter 6 Restoring the System
    1. Click 6.1 Restoring the Chassis
    2. Click 6.2 Incorporating a SPARC M10-4/M10-4S FRU into the System with the replacefru Command
    3. Click 6.3 Diagnosing a Replacement FRU
    4.  6.4 Restoring XSCF Setting Information
    5. Click 6.5 Incorporating a Chassis and I/O Device into a Physical Partition
    6.  6.6 Returning the Mode Switch to Locked Mode
    7.  6.7 Powering On the Physical Partition Requiring Maintenance
    8. Click 6.8 Starting the Entire System
  8. Chapter 7 Maintenance Flow
    1.  7.1 Maintenance Workflow
    2. Click 7.2 FRU Replacement Workflow
    3. Click 7.3 FRU Installation Workflow
    4. Click 7.4 FRU Removal Workflow
  9. Chapter 8 Maintaining the PCI Express Cards
    1.  8.1 Before Maintaining a PCI Express Card
    2.  8.2 PCI Express Card Configuration
    3.  8.3 FRU Removal and Installation Flow
    4. Click 8.4 Removing a PCI Express Card
    5. Click 8.5 Installing a PCI Express Card
  10. Chapter 9 Maintaining the CPU Memory Unit/Memory
    1.  9.1 Before Maintaining a CPU Memory Unit/Memory
    2. Click 9.2 Configuration of the CPU Memory Unit and Memory
    3.  9.3 Maintenance Precautions
    4.  9.4 FRU Removal and Installation Flow
    5. Click 9.5 Removing a CPU Memory Unit
    6.  9.6 Installing a PCI Express Cable
    7.  9.7 Switching the microSD Card
    8.  9.8 Removing Memory
    9.  9.9 Installing Memory
    10. Click 9.10 Installing a CPU Memory Unit
    11.  9.11 Checking the XCP Firmware Version
    12.  9.12 Checking the XCP Firmware Version (Building Block Configuration)
  11. Chapter 10 Maintaining the Internal Disks
    1.  10.1 Before Maintaining an Internal Disk
    2.  10.2 Configuration of the Internal Disks
    3.  10.3 FRU Removal and Installation Flow
    4.  10.4 Removing an Internal Disk
    5.  10.5 Installing an Internal Disk
  12. Chapter 11 Maintaining the Fan Units
    1.  11.1 Before Maintaining a Fan Unit
    2.  11.2 Configuration of the Fan Units
    3.  11.3 Removing a Fan Unit
    4.  11.4 Installing a Fan Unit
  13. Chapter 12 Maintaining the Power Supply Units
    1.  12.1 Before Maintaining a Power Supply Unit
    2.  12.2 Configuration of the Power Supply Units
    3.  12.3 Removing a Power Supply Unit
    4.  12.4 Installing a Power Supply Unit
  14. Chapter 13 Maintaining the PSU Backplane Unit/Operation Panel
    1.  13.1 Before Maintaining the PSU Backplane Unit/Operation Panel
    2.  13.2 Locations of the PSU Backplane Unit and Operation Panel
    3.  13.3 Maintenance Precautions
    4.  13.4 FRU Removal and Installation Flow
    5. Click 13.5 Removing the PSU Backplane Unit/Operation Panel
    6. Click 13.6 Installing the PSU Backplane Unit/Operation Panel
  15. Chapter 14 Maintaining the Crossbar Cables
    1.  14.1 Before Maintaining a Crossbar Cable
    2.  14.2 Configuration of the Crossbar Cable Connection Ports
    3.  14.3 Removing the Crossbar Cables
    4.  14.4 Installing the Crossbar Cables
  16. Chapter 15 Maintaining the Crossbar Units
    1.  15.1 Before Maintaining a Crossbar Unit
    2.  15.2 Configuration of the Crossbar Units
    3.  15.3 Removing a Crossbar Unit
    4.  15.4 Installing a Crossbar Unit
  17. Chapter 16 Maintaining the XSCF BB Control Cables
    1.  16.1 Before Maintaining an XSCF BB Control Cable
    2.  16.2 Configuration of the XSCF BB Control Ports
    3.  16.3 Removing an XSCF BB Control Cable
    4.  16.4 Installing an XSCF BB Control Cable
  18. Chapter 17 Maintaining the XSCF DUAL Control Cables
    1.  17.1 Before Maintaining an XSCF DUAL Control Cable
    2.  17.2 Configuration of the XSCF DUAL Control Ports
    3.  17.3 Removing an XSCF DUAL Control Cable
    4.  17.4 Installing an XSCF DUAL Control Cable
  19. Appendix A Component List
  20. Appendix B Component Specifications
    1.  B.1 CPU Memory Unit
    2.  B.2 Crossbar Unit
    3.  B.3 Power Supply Unit
    4.  B.4 Fan Unit
    5.  B.5 Internal Disk Drive
    6.  B.6 PCI Express Card
    7.  B.7 Backplanes
    8.  B.8 Operation Panel
  21. Appendix C Oracle Solaris Troubleshooting Commands
    1.  C.1 iostat Command
    2.  C.2 prtdiag Command
    3.  C.3 prtconf Command
    4.  C.4 netstat Command
    5.  C.5 ping Command
    6.  C.6 ps Command
    7.  C.7 prstat Command
  22. Appendix D External Interface Specifications
    1. Click D.1 Serial Port
    2.  D.2 USB Port
    3.  D.3 SAS Port
    4.  D.4 RESET Switch
  23. Appendix E Removing the Lithium Battery
    1.  E.1 Location of the Lithium Battery
    2.  E.2 Removing the Lithium Battery

5.8.1 Releasing of the SPARC M10-4S chassis (possible only in a system with a building block configuration)


5.8.1 Releasing of the SPARC M10-4S chassis (possible only in a system with a building block configuration)
In this section, power off the SPARC M10-4S requiring maintenance by using the replacefru command.
In the following execution example, maintenance is performed on an abnormal (Degraded) BB#0 chassis with four SPARC M10-4S units in a building block configuration.
Even in cases where the status of the SPARC M10-4S requiring maintenance is not abnormal (Degraded), perform the same procedure.
  1. Log in to the XSCF shell.
  2. Execute the replacefru command to display the maintenance menu.
XSCF> replacefru
  1. From the numeric keypad, select the FRU requiring maintenance.
    Since BB#0 is "Degraded," "1" is entered.
------------------------------------------------------------------------------

Maintenance/Replacement Menu
Please select the chassis including replaced FRU.

No. FRU Status
--- ------------------- --------------

1 /BB#0 Degraded
2 /BB#1 Normal
3 /BB#2 Normal
4 /BB#3 Normal
------------------------------------------------------------------------------

Select [1-4|c:cancel] :1
  1. From the numeric keypad, select the FRU requiring maintenance.
    Since the SPARC M10-4S chassis itself is to be maintained, "1" is entered.
------------------------------------------------------------------------------

Maintenance/Replacement Menu
Please select the BB or a type of FRU to be replaced.

1. BB itself（*1）

2. FAN (Fan Unit)

3. PSU (Power Supply Unit)

------------------------------------------------------------------------------

Select [1-3|c:cancel] :1
*1 The above "1. BB itself" is also displayed for the SPARC M10-4. However, the replacefru command cannot be used for maintenance of the chassis itself in the SPARC M10-4, so the maintenance work will be interrupted.
  1. From the numeric keypad, select the faulty FRU.
    Since BB#0 was confirmed faulty in step 3, "1" is also entered here.
------------------------------------------------------------------------------

Maintenance/Replacement Menu
Please select a FRU to be replaced.

No. FRU Status
--- ------------------- --------------

1 /BB#0 Degraded
------------------------------------------------------------------------------

Select [1|b:back] :1
  1. After confirming that the selected FRU is displayed, enter "r".
You are about to replace BB#0.
Do you want to continue?[r:replace|c:cancel] :r
  1. Confirm that the CHECK LED of the FRU is on or blinking.
    To release a SPARC M10-4S chassis itself, confirm that the system locator on the chassis is blinking.
    For details on the locations of LEDs, see "2.4.2 LEDs on the rear panel (System locator)" and "2.4.3 LEDs on each component."
Please execute the following steps:
1) Confirm the XSCF STANDBY LED of BB#0 is not lit.
2) Turn off the breaker of BB#0.
3) Remove BB#0.
4) Execute either the following:
4-1) After the exchanged device is connected with the system,
turn on the breaker of BB#0, and please select 'finish'.
4-2) If you want to suspend the maintenance without exchanging device,
please select 'cancel'.
[f:finish|c:cancel] :
You can now start FRU maintenance. Do not enter "f" until you complete the maintenance work.
After replacing the FRU, perform the work in "6.2.1 Incorporation of the SPARC M10-4S chassis (possible only in a system with a building block configuration)" to incorporate the FRU into the system.

Top of Page