Skip to main content
  1. Home >
  2. Products >
  3. Computing Products >
  4. Servers >
  5. Fujitsu SPARC servers >
  6. Downloads >
  7. User Manuals >
  8. Fujitsu SPARC M12-2S Installation Guide >
  9. 4.3.1 Crossbar Cable Connection for Direct Connections Between Chassis

Contents

  1. Preface
  2. Chapter 1 Understanding the Installation Flow
    1. Click 1.1 Workflows for the SPARC M12-2S
    2.  1.2 Workflow at Expansion With the PCI Expansion Unit
  3. Chapter 2 Planning and Preparing for System Installation
    1.  2.1 Safety Precautions
    2.  2.2 Items Requiring Confirmation Before Installation
    3. Click 2.3 Confirming the Physical Specifications of the System
    4. Click 2.4 Confirming Rack Specifications
    5. Click 2.5 Checking Environmental Conditions
    6.  2.6 Checking Acoustic Noise Levels
    7.  2.7 Checking Cooling Conditions
    8. Click 2.8 Checking the Power Input Type
    9. Click 2.9 Preparing Power Supply Facilities
    10. Click 2.10 Checking External Interface Port Specifications
    11.  2.11 Checking the Functions of the Operation Panel
  4. Chapter 3 Installing the System
    1.  3.1 Preparing the Necessary Tools/Information for Installation
    2. Click 3.2 Confirming Delivered Components
    3. Click 3.3 Installing the Rack
    4. Click 3.4 Mounting the SPARC M12-2S and the PCI Expansion Unit in a Rack
    5. Click 3.5 Mounting Optional Components
  5. Chapter 4 Setting the SPARC M12-2S in a Building Block Configuration
    1.  4.1 Setting the ID (BB-ID) Identifying the SPARC M12-2S
    2. Click 4.2 Connecting XSCF Cables
    3. Click 4.3 Connecting Crossbar Cables
    4. Click 4.4 Storing Crossbar Cables
  6. Chapter 5 Connecting Cables to the SPARC M12-2S and the PCI Expansion Unit
    1.  5.1 Connecting Cables to the SPARC M12-2S
    2.  5.2 Connecting Cables to the PCI Expansion Unit
    3.  5.3 Connecting Cables to the Crossbar Box
    4.  5.4 Storing Cables
  7. Chapter 6 Performing an Initial System Diagnosis
    1.  6.1 Connecting the System Management Terminal
    2. Click 6.2 Turning On the Input Power
    3.  6.3 Logging In to the XSCF
    4.  6.4 Confirming the XCP Firmware Version
    5.  6.5 Checking the Altitude Setting
    6.  6.6 Setting the Time
    7.  6.7 Performing a Diagnosis Test
    8.  6.8 Checking the Component Status
  8. Chapter 7 Making the Initial System Settings
    1.  7.1 Setting the Password Policy
    2.  7.2 Setting a User Account and Password
    3. Click 7.3 Configuring the Telnet/SSH Service
    4.  7.4 Configuring the HTTPS Service
    5. Click 7.5 Configuring the XSCF Network
    6.  7.6 Configuring Memory Mirroring
    7.  7.7 Creating a PPAR Configuration List
    8. Click 7.8 Assigning/Releasing a Physical System Board (PSB) for a Physical Partition (PPAR)
    9.  7.9 Synchronizing the Physical Partition (PPAR) Time and XSCF Time
    10. Click 7.10 Registering a CPU Activation Key
    11.  7.11 Assigning CPU Core Resources
    12. Click 7.12 Starting and Stopping a Physical Partition (PPAR)
    13.  7.13 Installing Oracle Solaris
    14. Click 7.14 Saving Configuration Information
  9. Chapter 8 Expanding a System With a Building Block Configuration
    1.  8.1 Points of Concern During Expansion
    2. Click 8.2 Preparation for Expansion
    3. Click 8.3 SPARC M12-2S Expansion Work
    4.  8.4 Incorporating the SPARC M12-2S to be Added
    5.  8.5 Initial Diagnosis of the SPARC M12-2S to be Added
  10. Chapter 9 Reducing a System With a Building Block Configuration
    1.  9.1 Points of Concern During Reduction
    2. Click 9.2 Preparation for Reduction
    3. Click 9.3 SPARC M12-2S Reduction Work
  11. Appendix A Troubleshooting
    1.  A.1 Understanding the Usual Problems and Their Corrective Actions
    2. Click A.2 Understanding Commands for Troubleshooting
    3. Click A.3 How to Restore a BB-ID From an Incorrect Setting
  12. Appendix B Cable Connection Information on Building Block Configurations
    1.  B.1 2BB Configuration (Direct Connections Between Chassis)
    2.  B.2 3BB Configuration (Direct Connections Between Chassis)
    3.  B.3 4BB Configuration (Direct Connections Between Chassis)
    4.  B.4 From the 2BB Configuration to 8BB Configuration (Connections via a Crossbar Box)
    5.  B.5 From the 9BB Configuration to 16BB Configuration (Connections via a Crossbar Box)
    6.  B.6 Power Cord Connections in Expansion Racks
  13. Appendix C Setup Command Workflow
  14. Appendix D Installation Procedure Checklist
    1.  D.1 From Installation of the 1BB Configuration to Initial Diagnosis
    2.  D.2 From Installation to Initial Diagnosis of Configuration With Direct Connections Between Chassis

4.3.1 Crossbar Cable Connection for Direct Connections Between Chassis


4.3.1 Crossbar Cable Connection for Direct Connections Between Chassis
Although the connection route varies depending on the BB configuration, the connection method is the same.
Each cable has an attached label showing the connection destination port. Connect the cable to the port corresponding to the label.
Since one port number is assigned to each pair of ports, connect crossbar cables in pairs.
For the port locations, see Figure 4-6, and for an example of the appearance of the label, see Figure 4-7.
Note that the given example assumes the 2BB configuration. For the connection order, cable routing diagram, and cable list for each configuration, see "Appendix B Cable Connection Information on Building Block Configurations."

  1. Check the labels of the crossbar cables, and bind the cables with hook-and-loop fastener strips.
    - Bind eight crossbar cables (optical) into one bundle with fastener strips.

    - Sort crossbar cables (electrical) by their connection to XBU#1 or XBU#0. At each of these destinations, bind four cables into one bundle with fastener strips.
Note - After connecting all the cables, store them in the rack. This procedure is described in "4.4 Storing Crossbar Cables." Do not perform the procedure now.
Figure 4-6  Crossbar Unit Port Numbers (SPARC M12-2S side)
Figure 4-6 Crossbar Unit Port Numbers (SPARC M12-2S side)
Figure 4-7  Example of the Appearance of a Crossbar Cable Label
Figure 4-7 Example of the Appearance of a Crossbar Cable Label
  1. Connect crossbar cables to the crossbar unit.
    Connect the crossbar cables to the locations of crossbar unit ports shown on the label.
    Hold the connector of the crossbar cable, and insert it straight into the opening. Do not hold the cable or its pull-tab part when inserting it.
Note - If you insert a connector with the pull-tab pulled, the connector may be damaged.
Note - There are three types of crossbar cable (optical). Connect crossbar cables of the same type to the same port numbers.
You can distinguish the type of crossbar cable by the pull-tab shape (A in Figure 4-8 or Figure 4-9).
Figure 4-8  Crossbar Cable (Optical) Shape and Pull-Tab
Figure 4-8 Crossbar Cable (Optical) Shape and Pull-Tab
Figure 4-9  Crossbar Cable (Electrical) Shape and Pull-Tab
Figure 4-9 Crossbar Cable (Electrical) Shape and Pull-Tab
  1. Connect the crossbar cables between XBU#1 of BB#00 and XBU#1 of BB#01.
    a. Connect the 0L ports (pink) of XBU#1.

    b. Connect the 0L ports (black) of XBU#1.

    c. Connect the 0R ports (light blue) of XBU#1.

    d. Connect the 0R ports (black) of XBU#1.
  1. Connect the crossbar cables between XBU#0 of BB#00 and XBU#0 of BB#01.
    a. Connect the 0L ports (pink) of XBU#0.

    b. Connect the 0L ports (black) of XBU#0.

    c. Connect the 0R ports (light blue) of XBU#0.

    d. Connect the 0R ports (black) of XBU#0.
  1. Confirm that the crossbar cables are correctly and firmly connected.
    With the crossbar cables connected to their ports, push in each cable while holding the joint (A in Figure 4-10 or Figure 4-11) at the base of the crossbar cable connector.
Note - A loose crossbar cable connection may, on rare occasions, cause an error due to poor connection. After connecting a crossbar cable, push it in again so that it is tightly in place to prevent any improper connection. Do not hold only the cable when performing the work at this time. Otherwise, the cable may bend out of shape.
Figure 4-10  Part to Hold When Checking a Crossbar Cable (Optical) Connection
Figure 4-10 Part to Hold When Checking a Crossbar Cable (Optical) Connection
Figure 4-11  Part to Hold When Checking a Crossbar Cable (Electrical) Connection
Figure 4-11 Part to Hold When Checking a Crossbar Cable (Electrical) Connection

Top of Page