Skip to main content

Contents

  1. Preface
  2. Chapter 1 Understanding the Installation Flow
    1. Click 1.1 Workflows for the SPARC M12-2S
    2.  1.2 Workflow at Expansion With the PCI Expansion Unit
  3. Chapter 2 Planning and Preparing for System Installation
    1.  2.1 Safety Precautions
    2.  2.2 Items Requiring Confirmation Before Installation
    3. Click 2.3 Confirming the Physical Specifications of the System
    4. Click 2.4 Confirming Rack Specifications
    5. Click 2.5 Checking Environmental Conditions
    6.  2.6 Checking Acoustic Noise Levels
    7.  2.7 Checking Cooling Conditions
    8. Click 2.8 Checking the Power Input Type
    9. Click 2.9 Preparing Power Supply Facilities
    10. Click 2.10 Checking External Interface Port Specifications
    11.  2.11 Checking the Functions of the Operation Panel
  4. Chapter 3 Installing the System
    1.  3.1 Preparing the Necessary Tools/Information for Installation
    2. Click 3.2 Confirming Delivered Components
    3. Click 3.3 Installing the Rack
    4. Click 3.4 Mounting the SPARC M12-2S and the PCI Expansion Unit in a Rack
    5. Click 3.5 Mounting Optional Components
  5. Chapter 4 Setting the SPARC M12-2S in a Building Block Configuration
    1.  4.1 Setting the ID (BB-ID) Identifying the SPARC M12-2S
    2. Click 4.2 Connecting XSCF Cables
    3. Click 4.3 Connecting Crossbar Cables
    4. Click 4.4 Storing Crossbar Cables
  6. Chapter 5 Connecting Cables to the SPARC M12-2S and the PCI Expansion Unit
    1.  5.1 Connecting Cables to the SPARC M12-2S
    2.  5.2 Connecting Cables to the PCI Expansion Unit
    3.  5.3 Connecting Cables to the Crossbar Box
    4.  5.4 Storing Cables
  7. Chapter 6 Performing an Initial System Diagnosis
    1.  6.1 Connecting the System Management Terminal
    2. Click 6.2 Turning On the Input Power
    3.  6.3 Logging In to the XSCF
    4.  6.4 Confirming the XCP Firmware Version
    5.  6.5 Checking the Altitude Setting
    6.  6.6 Setting the Time
    7.  6.7 Performing a Diagnosis Test
    8.  6.8 Checking the Component Status
  8. Chapter 7 Making the Initial System Settings
    1.  7.1 Setting the Password Policy
    2.  7.2 Setting a User Account and Password
    3. Click 7.3 Configuring the Telnet/SSH Service
    4.  7.4 Configuring the HTTPS Service
    5. Click 7.5 Configuring the XSCF Network
    6.  7.6 Configuring Memory Mirroring
    7.  7.7 Creating a PPAR Configuration List
    8. Click 7.8 Assigning/Releasing a Physical System Board (PSB) for a Physical Partition (PPAR)
    9.  7.9 Synchronizing the Physical Partition (PPAR) Time and XSCF Time
    10. Click 7.10 Registering a CPU Activation Key
    11.  7.11 Assigning CPU Core Resources
    12. Click 7.12 Starting and Stopping a Physical Partition (PPAR)
    13.  7.13 Installing Oracle Solaris
    14. Click 7.14 Saving Configuration Information
  9. Chapter 8 Expanding a System With a Building Block Configuration
    1.  8.1 Points of Concern During Expansion
    2. Click 8.2 Preparation for Expansion
    3. Click 8.3 SPARC M12-2S Expansion Work
    4.  8.4 Incorporating the SPARC M12-2S to be Added
    5.  8.5 Initial Diagnosis of the SPARC M12-2S to be Added
  10. Chapter 9 Reducing a System With a Building Block Configuration
    1.  9.1 Points of Concern During Reduction
    2. Click 9.2 Preparation for Reduction
    3. Click 9.3 SPARC M12-2S Reduction Work
  11. Appendix A Troubleshooting
    1.  A.1 Understanding the Usual Problems and Their Corrective Actions
    2. Click A.2 Understanding Commands for Troubleshooting
    3. Click A.3 How to Restore a BB-ID From an Incorrect Setting
  12. Appendix B Cable Connection Information on Building Block Configurations
    1.  B.1 2BB Configuration (Direct Connections Between Chassis)
    2.  B.2 3BB Configuration (Direct Connections Between Chassis)
    3.  B.3 4BB Configuration (Direct Connections Between Chassis)
    4.  B.4 From the 2BB Configuration to 8BB Configuration (Connections via a Crossbar Box)
    5.  B.5 From the 9BB Configuration to 16BB Configuration (Connections via a Crossbar Box)
    6.  B.6 Power Cord Connections in Expansion Racks
  13. Appendix C Setup Command Workflow
  14. Appendix D Installation Procedure Checklist
    1.  D.1 From Installation of the 1BB Configuration to Initial Diagnosis
    2.  D.2 From Installation to Initial Diagnosis of Configuration With Direct Connections Between Chassis

2.9.1 Electrical Specifications


2.9.1 Electrical Specifications
Table 2-9 to Table 2-13 list the electrical specifications of the SPARC M12-2S and PCI expansion unit.
Note - The values listed in Table 2-9 to Table 2-13 are based on values for the maximum configurations of the SPARC M12-2S and PCI expansion unit. The actual values vary depending on the system configuration.
Table 2-9  Electrical Specifications (SPARC M12-2S)
Item SPARC M12-2S (16 memory slots) SPARC M12-2S (24 memory slots)
Input voltage
200 to 240 VAC
200 to 240 VAC
Number of power cords
4 (1 for each PSU)
4 (1 for each PSU)
Power cord length Maximum length of 3.0 m (9.8 ft.) Maximum length of 3.0 m (9.8 ft.)
Redundancy 2+2 redundant configuration 2+2 redundant configuration
Frequency
50 Hz/60 Hz, single phase
50 Hz/60 Hz, single phase
Maximum input current (*1) 16.5 A 16.8 A
Maximum power consumption 3,224 W 3,292 W
Apparent power 3,290 VA 3,359 VA
Rush current (*2) 65 A peak or less
65 A peak or less
Leakage current (*2) 3.5 mA or less 3.5 mA or less
*1 The current that flows through each power cord is a fraction of the value listed in Table 2-9. In a redundant configuration, it is one-fourth the value. In a non-redundant configuration, it is up to one-half the value.

*2 The value is per power cord.
Table 2-10  Electrical Specifications (Expansion Rack: Single-Phase Feed Model) (*1)
Item Specification  
Expansion Rack 1 Only Available for Expansion Rack 2
Input voltage
200 to 240 VAC
200 to 240 VAC
Number of power cords 8 8
Power cord length 4.0 m (13.1 ft.) 4.0 m (13.1 ft.)
Redundancy (*2) 1+1 redundant configuration 1+1 redundant configuration
Frequency
50 Hz/60 Hz
50 Hz/60 Hz
Maximum input current (*3) Max. 40 A Maximum of 40 A
Maximum input current (*4) (*5) 6.9 A 9.0 A
Maximum power consumption (*4) 1,354 W 1,754 W
Apparent power (*4) 1,382 VA 1,790 VA
Rush current (*3) (*4)
80 A peak or less
80 A peak or less
Leakage current (*3) (*4) 3.5 mA or less 3.5 mA or less
*1 This shows the value for one rack.
*2 In the case where the SPARC M12-2S is mounted in the expansion rack. When any unit other than SPARC M12-2S is mounted, the value may vary with the power connection configuration of the unit.

*3 The value is the permissible value per power cord. The actual current value depends on the rated value of the devices mounted in the expansion rack.

*4 This is the value when no SPARC M12-2S or other device is mounted in the expansion rack (only the crossbar box is mounted).
Only two power cords consume power.
If the SPARC M12-2S and other devices are mounted, the current value and the number of power cords consuming power may vary.

*5 The current that flows through each power cord in a redundant configuration is half the value listed in Table 2-10.
Table 2-11  Electrical Specifications (Expansion Rack: Three-Phase Feed Model) (*1)
Item Specification  
Expansion Rack 1 Only Available for Expansion Rack 2
Input voltage
200 to 240 VAC
200 to 240 VAC
Number of power cords 6 6
Power cord length 4.0 m (13.1 ft.) 4.0 m (13.1 ft.)
Redundancy (*2) 1+1 redundant configuration 1+1 redundant configuration
Frequency
50 Hz/60 Hz
50 Hz/60 Hz
Maximum input current (*3) Max. 35 A Maximum of 35 A
Maximum input current (*4) (*5) 4.0 A 5.2 A
Maximum power consumption (*4) 1,354 W 1,754 W
Apparent power (*4) 1,382 VA 1,790 VA
Rush current (*3) (*4)
80 A peak or less
80 A peak or less
Leakage current (*3) (*4) 3.5 mA or less 3.5 mA or less
*1 This shows the value for one rack.
*2 In the case where the SPARC M12-2S is mounted in the expansion rack. When any unit other than SPARC M12-2S is mounted, the value may vary with the power connection configuration of the unit.

*3 The value is the permissible value per power cord. The actual current value depends on the rated value of the devices mounted in the expansion rack.

*4 This is the value when no SPARC M12-2S or other device is mounted in the expansion rack (only the crossbar box is mounted).
Only two power cords consume power.
If the SPARC M12-2S and other devices are mounted, the current value and the number of power cords consuming power may vary.

*5 The current that flows through each power cord in a redundant configuration is half the value listed in Table 2-11.
Table 2-12  Electrical Specifications (Expansion Rack: Three-Phase Star Feed Model)(*1)
Item Specification  
Expansion Rack 1 Only Available for Expansion Rack 2
Input voltage
380 to 415 VAC
380 to 415 VAC
Number of power cords 6 6
Power cord length 4.0 m (13.1 ft.) 4.0 m (13.1 ft.)
Redundancy (*2) 1+1 redundant configuration 1+1 redundant configuration
Frequency
50 Hz/60 Hz
50 Hz/60 Hz
Maximum input current (*3) Max. 24 A Maximum of 24 A
Maximum input current (*4) (*5) 2.1 A 2.7 A
Maximum power consumption (*4) 1,354 W 1,754 W
Apparent power (*4) 1,382 VA 1,790 VA
Rush current (*3) (*4)
80 A peak or less
80 A peak or less
Leakage current (*3) (*4) 3.5 mA or less 3.5 mA or less
*1 This shows the value for one rack.
*2 In the case where the SPARC M12-2S is mounted in the expansion rack. When any unit other than SPARC M12-2S is mounted, the value may vary with the power connection configuration of the unit.

*3 The value is the permissible value per power cord. The actual current value depends on the rated value of the devices mounted in the expansion rack.

*4 This is the value when no SPARC M12-2S or other device is mounted in the expansion rack (only the crossbar box is mounted).
Only two power cords consume power.
If the SPARC M12-2S and other devices are mounted, the current value and the number of power cords consuming power may vary.

*5 The current that flows through each power cord in a redundant configuration is half the value listed in Table 2-12.
Table 2-13  Electrical Specifications (PCI Expansion Unit)
Item Specification
  Input Voltage of 100 to 120 VAC Input Voltage of 200 to 240 VAC
Number of power cords
2 (1 for each PSU)
2 (1 for each PSU)
Power cord length Maximum length of 3.0 m (9.8 ft.) Maximum length of 3.0 m (9.8 ft.)
Redundancy 1+1 redundant configuration 1+1 redundant configuration
Frequency
50 Hz/60 Hz, single phase
50 Hz/60 Hz, single phase
Maximum input current (*1) 2.9 A 1.4 A
Maximum power consumption 279 W 270 W
Apparent power
284 VA
276 VA
Rush current (*2)
40 A peak or less
40 A peak or less
Leakage current (*2) 1.75 mA or less 1.75 mA or less
*1 The current that flows through each power cord in a redundant configuration is half the value listed in Table 2-13.

*2 The value is per power cord.

Top of Page