Skip to main content
  1. Home >
  2. Products >
  3. Computing Products >
  4. Servers >
  5. Fujitsu SPARC servers >
  6. Downloads >
  7. User Manuals >
  8. Fujitsu M10-1/SPARC M10-1 Service Manual >
  9. 6.5.3 Restoring the logical domain configuration information and OpenBoot PROM environment variables

Contents

  1. Preface
  2. Chapter 1 Before Starting Maintenance Work
    1.  1.1 Warning/Caution Indications
    2.  1.2 Labels/Tags
    3.  1.3 Safety Precautions
    4.  1.4 Precautions on Static Electricity
    5.  1.5 Other Precautions
    6.  1.6 Emergency Power Off
  3. Chapter 2 Understanding the System Components
    1.  2.1 Identifying the Names and Locations of Components
    2. Click 2.2 Checking the Memory Configuration Rules
    3. Click 2.3 Confirming the Functions of the Operation Panel
    4. Click 2.4 Checking the LED Indications
  4. Chapter 3 Types of Maintenance
    1.  3.1 Types of Maintenance Supported in the SPARC M10-1
    2.  3.2 Active Maintenance
    3.  3.3 System-stopped Maintenance (Inactive Maintenance)
  5. Chapter 4 Preparation and Precautions for Maintenance
    1. Click 4.1 Confirming the System Configuration
    2. Click 4.2 Troubleshooting
    3. Click 4.3 Maintenance Precautions
  6. Chapter 5 Preparations Required for Maintenance
    1.  5.1 Preparing Tools Required for Maintenance
    2.  5.2 Switching the Mode Switch to Service Mode
    3. Click 5.3 Checking the Operating Condition and Resource Usage Status
    4. Click 5.4 Enabling the Removal of an Internal Disk
    5. Click 5.5 Stopping the Entire System
    6. Click 5.6 Saving Setting Information and Configuration Information
    7.  5.7 Releasing a FRU from the System with the replacefru Command
    8. Click 5.8 Accessing a FRU
  7. Chapter 6 Understanding the Preparations for Restoring the System
    1. Click 6.1 Restoring the Chassis
    2.  6.2 Incorporating a FRU into the System with the replacefru Command
    3. Click 6.3 After Replacing the Motherboard Unit/PSU Backplane
    4.  6.4 Diagnosing a Replacement FRU
    5. Click 6.5 Restoring Setting Information and Configuration Information
    6.  6.6 Incorporating an Internal Disk
    7.  6.7 Checking the FRU Status after Maintenance
    8.  6.8 Returning the Mode Switch to Locked Mode
    9. Click 6.9 Starting the System
  8. Chapter 7 Maintenance Flow
    1.  7.1 Maintenance Workflow
    2. Click 7.2 FRU Replacement Workflow
    3. Click 7.3 FRU Installation Workflow
    4. Click 7.4 FRU Removal Workflow
  9. Chapter 8 Maintaining the PCI Express Cards
    1.  8.1 Before Maintaining a PCI Express Card
    2.  8.2 PCI Express Card Configuration
    3. Click 8.3 Removing a PCI Express Card
    4. Click 8.4 Installing a PCI Express Card
  10. Chapter 9 Maintaining the Internal Disks
    1.  9.1 Before Maintaining an Internal Disk
    2.  9.2 Configuration of the Internal Disks
    3.  9.3 Removing an Internal Disk
    4.  9.4 Installing an Internal Disk
  11. Chapter 10 Maintaining the HDD Backplane
    1.  10.1 Before Maintaining the HDD Backplane
    2.  10.2 HDD Backplane Location
    3. Click 10.3 Removing the HDD Backplane
    4. Click 10.4 Installing the HDD Backplane
  12. Chapter 11 Maintaining the Power Supply Units
    1.  11.1 Before Maintaining a Power Supply Unit
    2.  11.2 Configuration of the Power Supply Units
    3. Click 11.3 Removing a Power Supply Unit
    4. Click 11.4 Installing a Power Supply Unit
  13. Chapter 12 Maintaining the PSU Backplane
    1.  12.1 Before Maintaining the PSU Backplane
    2.  12.2 PSU Backplane Location
    3.  12.3 Precautions for Maintaining the PSU Backplane
    4. Click 12.4 Removing the PSU Backplane
    5. Click 12.5 Installing the PSU Backplane
  14. Chapter 13 Maintaining the Cable Kit
    1.  13.1 Before Maintaining the Cable Kit
    2.  13.2 Cable Kit Location
    3. Click 13.3 Removing the Cable Kit
    4. Click 13.4 Installing the Cable Kit
  15. Chapter 14 Maintaining the Operation Panel
    1.  14.1 Before Maintaining the Operation Panel
    2.  14.2 Operation Panel Location
    3. Click 14.3 Removing the Operation Panel
    4. Click 14.4 Installing the Operation Panel
  16. Chapter 15 Maintaining the Fan Units
    1.  15.1 Before Maintaining a Fan Unit
    2.  15.2 Configuration of the Fan Units
    3. Click 15.3 Removing a Fan Unit
    4. Click 15.4 Installing a Fan Unit
  17. Chapter 16 Maintaining the Motherboard Unit/Memory
    1.  16.1 Before Maintaining the Motherboard Unit/Memory
    2.  16.2 Motherboard Unit Location
    3.  16.3 Memory Locations
    4.  16.4 Precautions for Motherboard Unit Replacement
    5. Click 16.5 Removing the Motherboard Unit and Memory
    6. Click 16.6 Installing the Motherboard Unit and Memory
  18. Appendix A Component List
  19. Appendix B Component Specifications
    1.  B.1 Motherboard Unit
    2.  B.2 Power Supply Unit
    3.  B.3 Fan Unit
    4.  B.4 Internal Disk
    5.  B.5 PCI Express Card
    6.  B.6 Backplanes
    7.  B.7 Operation Panel
  20. Appendix C Oracle Solaris Troubleshooting Commands
    1.  C.1 iostat Command
    2.  C.2 prtdiag Command
    3.  C.3 prtconf Command
    4.  C.4 netstat Command
    5.  C.5 ping Command
    6.  C.6 ps Command
    7.  C.7 prstat Command
  21. Appendix D External Interface Specifications
    1. Click D.1 Serial Port
    2.  D.2 USB Port
    3.  D.3 SAS Port
    4.  D.4 RESET Switch
  22. Appendix E Removing the Lithium Battery
    1.  E.1 Location of the Lithium Battery
    2.  E.2 Removing the Lithium Battery

6.5.3 Restoring the logical domain configuration information and OpenBoot PROM environment variables


6.5.3 Restoring the logical domain configuration information and OpenBoot PROM environment variables
Reflect the setting of the XML file saved in "5.6.3 Saving the logical domain configuration information and OpenBoot PROM environment variables," and execute the shutdown command and restart the control domain.
The following shows the procedure for restoring the saved configuration information of the logical domains.
  1. Confirm that the current logical domain configuration is factory-default.
primary# ldm list-config | grep "factory-default"
factory-default [current]
  1. If [current] does not appear beside "factory-default," the current logical domain configuration is not factory-default. In such a case, follow the procedure below to change the current logical domain configuration to factory-default.
    a. Execute the ldm set-spconfig command with "factory-default" specified.
primary# ldm set-spconfig factory-default
  1. b. Execute the poweroff command of the XSCF firmware and turn off the power to the physical partition.
XSCF> poweroff -p ppar_id
  1. The OpenBoot PROM environment variables are initialized. So, reset it to the original values.
    a. To stop in the OpenBoot PROM state, confirm "auto-boot?" out of the OpenBoot PROM environment variables.
    If the value is "true", change it to "false".
XSCF> setpparparam -p 0 -s bootscript "setenv auto-boot? false"
PPAR-ID of PPARs that will be affected:0
OpenBoot PROM variable bootscript will be changed.
Continue? [y|n] :y
  1. b. If you change the setting, confirm the OpenBoot PROM environment variables.
XSCF> showpparparam -p 0
use-nvramrc :-
security-mode :-
bootscript :
setenv auto-boot? false
  1. c. Execute the poweron command to restart the physical partition.
XSCF> poweron -p 0
  1. d. Execute the showdomainstatus command to check the status of the control domain.
    Confirm that the status of the control domain is displayed as "OpenBoot Running" indicating that it is in the OpenBoot PROM state.
XSCF> showdomainstatus -p 0
Logical Domain Name Status
primary OpenBoot Running
  1. e. Execute the console command to switch to the control domain console.
XSCF> console -p 0 -y
Console contents may be logged.
Connect to PPAR-ID 0?[y|n] :y
  1. f. Restore the OpenBoot PROM environment variables based on the record saved in "5.6.3 Saving the logical domain configuration information and OpenBoot PROM environment variables."
    The following example restores the boot-device to "/pci@8000/pci@4/pci@0/pci@0/scsi@0/disk@p0,0".
{0} ok setenv boot-device /pci@8000/pci@4/pci@0/pci@0/scsi@0/disk@p0,0
boot-device = /pci@8000/pci@4/pci@0/pci@0/scsi@0/disk@p0,0
{0} ok printenv boot-device
boot-device = /pci@8000/pci@4/pci@0/pci@0/scsi@0/disk@p0,0
 The following example restores "auto-boot?" to "true."
{0} ok setenv auto-boot? true
auto-boot? = true
{0} ok printenv auto-boot?
auto-boot? = true
  1. Boot Oracle Solaris.
{0} ok boot
  1. On Oracle Solaris super user prompt, confirm that the system started with factory-default.
primary# ldm ls-spconfig
factory-default [current]
  1. Execute the ldm init-system command to reflect the setting in the saved XML file.
    This is an example of restoring configuration information saved in /ldm-set1.xml.
primary# ldm init-system -i /ldm-set1.xml
Initiating a delayed reconfiguration operation on the primary domain.
All configuration changes for other domains are disabled until the primary
domain reboots, at which time the new configuration for the primary domain
will also take effect.
  1. Execute the shutdown command, and restart the control domain.
primary# shutdown -y -g0 -i6
  1. Bind resources to a physical domain other than the control domain, and start the domain.
    In the following example, the user binds resources to ldom1 and starts it.
primary# ldm bind ldom1
primary# ldm start ldom1
Note - If the virtual function (VF) is lent to the logical domains by using the SR-IOV function, the configuration of the virtual function may not be restored. Execute the ldm command to manually restore the virtual function that is not restored.
The following is an example.
primary# ldm create-vf /SYS/PCI1/IOVNET.PF0
primary# ldm add-io /SYS/PCI1/IOVNET.PF0.VF0 ldom1
  1. Execute the ldm add-spconfig command to save the configuration information of the logical domains.
    To save configuration information under the same name, execute rm-config to delete it once and then save it.

Top of Page