Skip to main content
  1. Home >
  2. Products >
  3. Computing Products >
  4. Servers >
  5. Fujitsu SPARC servers >
  6. Downloads >
  7. User Manuals >
  8. Fujitsu M10-1/SPARC M10-1 Service Manual >
  9. 4.1.2 Confirming the software and firmware configurations

Contents

  1. Preface
  2. Chapter 1 Before Starting Maintenance Work
    1.  1.1 Warning/Caution Indications
    2.  1.2 Labels/Tags
    3.  1.3 Safety Precautions
    4.  1.4 Precautions on Static Electricity
    5.  1.5 Other Precautions
    6.  1.6 Emergency Power Off
  3. Chapter 2 Understanding the System Components
    1.  2.1 Identifying the Names and Locations of Components
    2. Click 2.2 Checking the Memory Configuration Rules
    3. Click 2.3 Confirming the Functions of the Operation Panel
    4. Click 2.4 Checking the LED Indications
  4. Chapter 3 Types of Maintenance
    1.  3.1 Types of Maintenance Supported in the SPARC M10-1
    2.  3.2 Active Maintenance
    3.  3.3 System-stopped Maintenance (Inactive Maintenance)
  5. Chapter 4 Preparation and Precautions for Maintenance
    1. Click 4.1 Confirming the System Configuration
    2. Click 4.2 Troubleshooting
    3. Click 4.3 Maintenance Precautions
  6. Chapter 5 Preparations Required for Maintenance
    1.  5.1 Preparing Tools Required for Maintenance
    2.  5.2 Switching the Mode Switch to Service Mode
    3. Click 5.3 Checking the Operating Condition and Resource Usage Status
    4. Click 5.4 Enabling the Removal of an Internal Disk
    5. Click 5.5 Stopping the Entire System
    6. Click 5.6 Saving Setting Information and Configuration Information
    7.  5.7 Releasing a FRU from the System with the replacefru Command
    8. Click 5.8 Accessing a FRU
  7. Chapter 6 Understanding the Preparations for Restoring the System
    1. Click 6.1 Restoring the Chassis
    2.  6.2 Incorporating a FRU into the System with the replacefru Command
    3. Click 6.3 After Replacing the Motherboard Unit/PSU Backplane
    4.  6.4 Diagnosing a Replacement FRU
    5. Click 6.5 Restoring Setting Information and Configuration Information
    6.  6.6 Incorporating an Internal Disk
    7.  6.7 Checking the FRU Status after Maintenance
    8.  6.8 Returning the Mode Switch to Locked Mode
    9. Click 6.9 Starting the System
  8. Chapter 7 Maintenance Flow
    1.  7.1 Maintenance Workflow
    2. Click 7.2 FRU Replacement Workflow
    3. Click 7.3 FRU Installation Workflow
    4. Click 7.4 FRU Removal Workflow
  9. Chapter 8 Maintaining the PCI Express Cards
    1.  8.1 Before Maintaining a PCI Express Card
    2.  8.2 PCI Express Card Configuration
    3. Click 8.3 Removing a PCI Express Card
    4. Click 8.4 Installing a PCI Express Card
  10. Chapter 9 Maintaining the Internal Disks
    1.  9.1 Before Maintaining an Internal Disk
    2.  9.2 Configuration of the Internal Disks
    3.  9.3 Removing an Internal Disk
    4.  9.4 Installing an Internal Disk
  11. Chapter 10 Maintaining the HDD Backplane
    1.  10.1 Before Maintaining the HDD Backplane
    2.  10.2 HDD Backplane Location
    3. Click 10.3 Removing the HDD Backplane
    4. Click 10.4 Installing the HDD Backplane
  12. Chapter 11 Maintaining the Power Supply Units
    1.  11.1 Before Maintaining a Power Supply Unit
    2.  11.2 Configuration of the Power Supply Units
    3. Click 11.3 Removing a Power Supply Unit
    4. Click 11.4 Installing a Power Supply Unit
  13. Chapter 12 Maintaining the PSU Backplane
    1.  12.1 Before Maintaining the PSU Backplane
    2.  12.2 PSU Backplane Location
    3.  12.3 Precautions for Maintaining the PSU Backplane
    4. Click 12.4 Removing the PSU Backplane
    5. Click 12.5 Installing the PSU Backplane
  14. Chapter 13 Maintaining the Cable Kit
    1.  13.1 Before Maintaining the Cable Kit
    2.  13.2 Cable Kit Location
    3. Click 13.3 Removing the Cable Kit
    4. Click 13.4 Installing the Cable Kit
  15. Chapter 14 Maintaining the Operation Panel
    1.  14.1 Before Maintaining the Operation Panel
    2.  14.2 Operation Panel Location
    3. Click 14.3 Removing the Operation Panel
    4. Click 14.4 Installing the Operation Panel
  16. Chapter 15 Maintaining the Fan Units
    1.  15.1 Before Maintaining a Fan Unit
    2.  15.2 Configuration of the Fan Units
    3. Click 15.3 Removing a Fan Unit
    4. Click 15.4 Installing a Fan Unit
  17. Chapter 16 Maintaining the Motherboard Unit/Memory
    1.  16.1 Before Maintaining the Motherboard Unit/Memory
    2.  16.2 Motherboard Unit Location
    3.  16.3 Memory Locations
    4.  16.4 Precautions for Motherboard Unit Replacement
    5. Click 16.5 Removing the Motherboard Unit and Memory
    6. Click 16.6 Installing the Motherboard Unit and Memory
  18. Appendix A Component List
  19. Appendix B Component Specifications
    1.  B.1 Motherboard Unit
    2.  B.2 Power Supply Unit
    3.  B.3 Fan Unit
    4.  B.4 Internal Disk
    5.  B.5 PCI Express Card
    6.  B.6 Backplanes
    7.  B.7 Operation Panel
  20. Appendix C Oracle Solaris Troubleshooting Commands
    1.  C.1 iostat Command
    2.  C.2 prtdiag Command
    3.  C.3 prtconf Command
    4.  C.4 netstat Command
    5.  C.5 ping Command
    6.  C.6 ps Command
    7.  C.7 prstat Command
  21. Appendix D External Interface Specifications
    1. Click D.1 Serial Port
    2.  D.2 USB Port
    3.  D.3 SAS Port
    4.  D.4 RESET Switch
  22. Appendix E Removing the Lithium Battery
    1.  E.1 Location of the Lithium Battery
    2.  E.2 Removing the Lithium Battery

4.1.2 Confirming the software and firmware configurations


4.1.2 Confirming the software and firmware configurations
The software and firmware configurations and versions affect system operation. To change the configuration or investigate a problem, check the latest state and check for any problems in the software.
Confirming the software configuration
Use Oracle Solaris commands to check the software configuration.
If you are logged in to the XSCF console, switch to the control domain console by executing the console command beforehand.
Table 4-1 lists the commands used for checking the software configuration.
Table 4-1  Commands for checking the software configuration
Command Description
pkg (Oracle Solaris 11)
showrev (Oracle Solaris 10)		 Displays Oracle Solaris correction information and the version.
ldm Displays logical domain configuration information.
  1. Log in to the control domain console of the physical partition where the FRU requiring maintenance is mounted.
    For details on how to log in to the control domain console, see "8.3 Switching to the Control Domain Console From the XSCF Shell" in the Fujitsu SPARC M12 and Fujitsu M10/SPARC M10 System Operation and Administration Guide.
  2. Execute the pkg command to display Oracle Solaris correction information and the version.
  1. For Oracle Solaris 11, execute the pkg command.
# pkg info entire
Name: entire
Summary: entire incorporation including Support Repository Update (Oracle Solaris 11.1.12.5.0).
  1. For Oracle Solaris 10, execute the showrev command.
# showrev -p
  1. To display the Oracle VM Server for SPARC version, execute the ldm command.
# ldm -V
Logical Domains Manager (v 3.1)

Hypervisor control protocol v 1.9
Using Hypervisor MD v 1.3
  1. The following is examples of executing commands to check logical domain configuration information.

    When checking from Oracle Solaris on the control domain
# ldm list-spconfig
factory-default (*1)
confirm_service_manual [current] (*2)
#
*1 factory-default configuration
*2 Currently running logical domain configuration

  1. When checking from the XSCF shell
XSCF> showdomainconfig -p 0
PPAR-ID :0
Booting config
(Current) :confirm_service_manual (*1)
(Next) :confirm_service_manual
-----------------------------------------------------------------------------

Index :1
config_name :factory-default (*2)
domains :1
date_created:-
-----------------------------------------------------------------------------

Index :2
config_name :config_develop_env
domains :3
date_created:'2016-05-24 19:40:55'
XSCF>
*1 Currently running logical domain configuration
*2 factory-default configuration

Confirming the firmware configuration
Check the XCP firmware version by using the version command, which is an XSCF shell command.
  1. Log in to the XSCF shell.
  2. Execute the version command to confirm the firmware version information.
    In the following example, "-c xcp" is entered to confirm the overall XCP version.
XSCF> version -c xcp
BB#00-XSCF#0 (Master)
XCP0 (Reserve): 2360  (*1)
XCP1 (Current): 2360  (*2)
BB#01-XSCF#0 (Standby)
XCP0 (Reserve): 2360
XCP1 (Current): 2360 
*1 Version of the XCP firmware installed at Reserve on the SPARC M10-4S with BB-ID 00
*2 Version of the XCP firmware running on the SPARC M10-4S with BB-ID 00
Check the firmware version of the PCI expansion unit by using the ioxadm command, which is an XSCF shell command.
  1. Log in to the XSCF shell.
  2. Identify the mounting locations of the PCI expansion unit and link card.
XSCF> ioxadm list
PCIBOX Link
PCIBOX#2007 BB#00-PCI#7 (*1)
PCIBOX#2006 BB#00-PCI#5
PCIBOX#2005 BB#00-PCI#3
PCIBOX#2004 BB#00-PCI#1
*1 Mounting locations of the PCI expansion unit and link card
  1. Execute the ioxadm command to check the firmware version information for the PCI expansion unit and link card.
XSCF> ioxadm -v list
Location Type FW Ver Serial Num Part Num State
PCIBOX#2007 PCIBOX - PZ21242007 On
PCIBOX#2007/PSU#0 PSU - FEJD1212000530 CA01022-0750-D/ On
PCIBOX#2007/PSU#1 PSU - FEJD1212000529 CA01022-0750-D/ On
PCIBOX#2007/IOB IOBOARD 1330 PP123300E5 CA20365-B66X 008AG On (*1)
PCIBOX#2007/LINKBD BOARD - PP141900V0 CA20365-B60X 008AD/7061035 On
PCIBOX#2007/FANBP FANBP - PP123203NT CA20365-B68X 004AC On
BB#00-PCI#07 CARD 1330 PP133200UF CA20365-B59X 008AD/7061040 On (*2)
*1 Firmware version on the I/O board
*2 Firmware version on the link card

Top of Page