Problems Resolved in Oracle Solaris 11.3
Problems Resolved in Oracle Solaris 11.3
The following table lists the problems resolved in Oracle Solaris 11.3. You might encounter them in supported releases earlier than Oracle Solaris 11.3.
| Bug | 15813959 15813960 (7196117) |
| Model | SPARC M12-1, SPARC M12-2, SPARC M12-2S, SPARC M10-1, SPARC M10-4, SPARC M10-4S |
| Description | A PCI expansion unit is added using Oracle Solaris hotplug(1M) in a SPARC M12/M10 system. However, devices on the PCI expansion unit are not recognized. |
| Workaround | Before you add a PCI expansion unit by hotplug(1M), add the following line in the /etc/system file in advance and restart Oracle Solaris. set pcicfg:pcicfg_slot_busnums = 4 Note that the system does not recognize a device of a PCI expansion unit if you add the PCI expansion unit by PHP to a root complex that has been added by either of the following: the dynamic reconfiguration of the physical partition, or the Dynamic PCIe bus assignment. If this problem occurs, restart the logical domain to which the PCI expansion unit is assigned to make the system recognize the device of the PCI expansion unit. |
| Bug | 17430911 |
| Model | SPARC M12-1, SPARC M12-2, SPARC M12-2S |
| Description | When you change the power-saving operation of the physical partition from "elastic" to "disabled," the CPU frequency assigned to the logical domain may not increase. |
| Workaround | This has been modified with SRU 11.2.8.4.0 (Oracle VM Server for SPARC 3.2). Install SRU 11.2.8.4.0 or later on the control domain. [How to restore] Execute the Oracle Solaris svcadm command in the control domain to restart the ldmd services. primary# svcadm restart ldmd |
| Bug | 17561541 |
| Model | SPARC M12-1, SPARC M12-2, SPARC M12-2S, SPARC M10-1, SPARC M10-4, SPARC M10-4S |
| Description | In a SPARC M10 environment with XCP 2230 or later applied, or in a SPARC M12 environment with XCP 3021 or later applied, suppose that the ldm add-io command is executed after the ldm remove-io command was executed during delayed reconfiguration. Then, the ldmd daemon may cause a core dump and restart. |
| Workaround | This has been modified with SRU 11.2.8.4.0 and Oracle VM Server for SPARC 3.2 for Oracle Solaris 10. During delayed reconfiguration, execute the ldm remove-io command after executing the ldm add-io command. |
| Bug | 18502702 |
| Model | SPARC M10-1, SPARC M10-4, SPARC M10-4S |
| Description | If the SunVTS 7.0 ps17. 1 test is started on a SPARC M10 system with SPARC64 X+ processors, it may end with an error. |
| Workaround | This has been modified with SRU 11.2.1.5.0 and patch 151265-03 for Oracle Solaris 10. |
| Bug | 18595023 |
| Model | SPARC M12-1, SPARC M12-2, SPARC M12-2S, SPARC M10-1, SPARC M10-4, SPARC M10-4S |
| Description | If the ldm list-io command is executed after PCI cards, which support the SR-IOV function, are mounted on PCI expansion unit SLOT4 or higher, the pseudonym of the physical function of the PCI cards mounted in SLOT4 or higher is mistakenly shown as SLOT2. Moreover, the virtual functions created from the physical functions of the PCI cards that are mounted on SLOT4 or higher cannot be assigned to logical domains. [Example of command output] # ldm ls-io -l NAME TYPE BUS DOMAIN STATUS ---- ---- --- ------ ------ ... /SYS/PCI1/SLOT5 PCIE PCIE1 primary OCC [pci@8100/pci@4/pci@0/pci@1/pci@0/pci@0/pci@0/pci@1/pci@0/pci@10/pci@0/pci@1] network@0 network@0,1 ... /SYS/PCI1/SLOT2/IOVNET.PF0 PF PCIE1 primary [pci@8100/pci@4/pci@0/pci@1/pci@0/pci@0/pci@0/pci@1/pci@0/pci@10/pci@0/pci@1/network@0] maxvfs = 7 ... |
| Workaround | This has been modified with SRU 11.2.2.5.0 and patch 150817-03 for Oracle Solaris 10. |
| Bug | 18615814 |
| Model | SPARC M12-1, SPARC M12-2, SPARC M12-2S, SPARC M10-1, SPARC M10-4, SPARC M10-4S |
| Description | An I/O domain may output the following message, and Oracle Solaris panic may occur if a system board is deleted by executing dynamic reconfiguration of physical partitions (PPAR DR) or a PCIe end point device is dynamically removed from the I/O domain by executing the ldm remove-io command. panic[cpuX]/thread=XXXXXXXXXXXX: mutex_exit: not owner, lp=XXXXXXXX owner=X thread=XXXXXXXXXXXX |
| Workaround | This has been modified with SRU 11.2.8.4.0. Execute the svcadm(1M) command on the I/O domain to disable the intrd(1M) service before deleting the system board by executing dynamic reconfiguration of physical partitions (PPAR DR) or before removing the PCIe end point device from the I/O domain. # svcadm disable intrd Enable the intrd(1M) service after the process of the ldm remove-io command is completed. # svcadm enable intrd |
| Bug | 18665751 |
| Model | SPARC M10-1, SPARC M10-4, SPARC M10-4S |
| Description | When using XCP 2210, the Dynamic Resource Management (DRM) feature of Oracle VM Server for SPARC does not work. |
| Workaround | This has been modified with SRU 11.2.8.4.0 and Oracle VM Server for SPARC 3.2 for Oracle Solaris 10. Update the XCP firmware to XCP 2220 or later. |
| Bug | 18747641 |
| Model | SPARC M10-1, SPARC M10-4, SPARC M10-4S |
| Description | Core dumps may be produced or wrong calculation results may be obtained or a panic may occur when a program, which performs double-precision floating point instructions after enabling SPARC64 X/SPARC64 X+ processor-specific options and 4-byte boundary alignment (*1) and compiled with Oracle Solaris Studio compiler version 12.3 2013/06/17 or newer, is executed on a SPARC M10 system with Oracle Solaris 11.1 or newer. *1 The 4-byte boundary alignment is enabled by default when creating 64-bit programs. In the case of 32-bit programs, it is enabled if "-xmemalign=Ns (N=1,2,4,8,16)" or "-fast" is not specified. [Procedure of checking compiler version] The "-V" option shows version information. The date is output at the end of version notation. The compiler version that corresponds to this bug is 2013/06/17 or newer. $ cc -V cc: Sun C 5.12 SunOS_sparc Patch 148917-06 2013/06/17 $ f95 -V (f90 and f77 are also same.) f95: Sun Fortran 95 8.6 SunOS_sparc Patch 148517-05 2013/06/17 $ CC -V CC: Sun C++ 5.12 SunOS_sparc Patch 148506-11 2013/06/17 |
| Workaround | This has been modified with SRU 11.2.4.6.0. Recompile the program with the following "-xarch" flag. -xarch=sparcima |
| Bug | 19074260 |
| Model | SPARC M10-4S |
| Description | The following messages may be output in the log of ldoms/ldmd services (/var/svc/log/ldomsldmd:default.log), and the communication between the ldmd daemon and the XSCF may be disconnected during or after physical partition dynamic reconfiguration (PPAR DR). [Example of message] Sep 18 13:31:37 warning: Device busy: open_ldc_channel: Open of/devices/virtual-devices@100/channel-devices@200/virtual-channel@3:spds failed After that time, processes which need to communicate with XSCF such as PPAR DR or ldm list-spconfig command fail. |
| Workaround | This has been modified with SRU 11.2.8.4.0. [How to restore] Execute Oracle Solaris svcadm(1M) command to restart the ldoms/ldmd services. # svcadm restart ldmd |
| Bug | 19310540 |
| Model | SPARC M10-4S |
| Description | If the addboard(8) command is executed in the "factory-default" configuration, CPU cores may not be assigned to the control domain. |
| Workaround | This has been modified with SRU 11.2.8.4.0 and Oracle VM Server for SPARC 3.2 for Oracle Solaris 10. Add the CPU cores or threads which were not added, using the ldm add-core command or the ldm add-vcpu command. |
| Bug | 19310550 |
| Model | SPARC M12-2S, SPARC M10-4S |
| Description | On a physical partition, to which 8 or more system boards have been assigned, when collecting dump files of the hypervisor which is executed as the ldoms/ldmd service is started, the following console message is output by the ldoms/ldmd service, and it may fall back to maintenance mode. [Example of message] Feb 28 16:19:39 svc.startd[11]: ldoms/ldmd:default failed: transitioned to maintenance (see 'svcs -xv' for details) |
| Workaround | This has been modified with SRU 11.2.8.4.0 and Oracle VM Server for SPARC 3.2 for Oracle Solaris 10. [How to restore] Use the following process to change the timeout value of starting the ldoms/ldmd service to 600. # svccfg -s ldmd listprop : start/timeout_seconds count 180 : # svccfg -s ldmd setprop start/timeout_seconds=600 # svccfg -s ldmd listprop : start/timeout_seconds count 600 : # svcadm refresh ldmd # svcadm restart ldmd |
| Bug | 19358400 |
| Model | SPARC M12-1, SPARC M12-2, SPARC M12-2S, SPARC M10-1, SPARC M10-4, SPARC M10-4S |
| Description | If the root complex is dynamically added/deleted, the PCIe end point device configuration information shown by the showpparinfo(8) command will not reflect the PCIe end point device under the added/deleted root complex. |
| Workaround | This has been modified with SRU 11.2.9.5.0. [How to restore] By restarting the logical domain that added/deleted the root complex dynamically, the showpparinfo(8) command displays the correct configuration information. |
| Bug | 19424242 |
| Model | SPARC M12-1, SPARC M12-2, SPARC M12-2S, SPARC M10-1, SPARC M10-4, SPARC M10-4S |
| Description | On a system to which Oracle VM Server for SPARC 3.1.0.1 or later is applied, the following event may occur: If all CPUs or memory in an I/O domain are degraded due to a CPU or memory failure, the ldmd service abnormally terminates, and, as a result, the ldm(1M) command terminates with an error. |
| Workaround | This has been modified with SRU 11.2.8.4.0 and Oracle VM Server for SPARC 3.2 for Oracle Solaris 10. [How to restore] Replace the faulty CPU or memory. If you want to start Oracle Solaris while leaving the faulty CPU or memory installed, perform the following procedure on the XSCF: 1. Power off the physical partition (PPAR) by the poweroff(8) command. 2. Execute the setdomainconfig(8) command to place the PPAR in the factory-default state. XSCF> setdomainconfig -p ppar_id -c default 3. Execute the poweron(8) command to activate the PPAR. Oracle Solaris reboots in a configuration that includes only the control domain (factory-default). |
| Bug | 19424359 |
| Model | SPARC M12-1, SPARC M12-2, SPARC M12-2S, SPARC M10-1, SPARC M10-4, SPARC M10-4S |
| Description | If the domain configuration is restored in the degraded configuration, both of the following settings are reset to their default values: the setting specifying whether to enable/disable hypervisor dump collection and the setting specifying whether to enable/disable automatic reboot during hypervisor dump collection. [Default values] Hypervisor dump collection: Enabled Automatic reboot during hypervisor dump collection: Disabled |
| Workaround | This has been modified with SRU 11.2.8.4.0 and Oracle VM Server for SPARC 3.2 for Oracle Solaris 10. [How to restore] After executing the Oracle VM Server for SPARC ldm(1M) command to change the hypervisor dump setting, save the domain configuration information. # ldm set-hvdump hvdump=XXXX hvdump-reboot=YYYY # ldm add-spconfig ZZZZ After replacing the faulty component, execute the setdomainconfig(8) command to initiate a reboot with the original domain configuration. |
| Bug | 19513561 |
| Model | SPARC M12-1, SPARC M12-2, SPARC M12-2S, SPARC M10-1, SPARC M10-4, SPARC M10-4S |
| Description | The ldmd daemon of Oracle VM Server for SPARC may repeat the core dump if suspend processing of the appropriate domain fails during live migration. |
| Workaround | This has been modified with SRU 11.2.8.4.0 and Oracle VM Server for SPARC 3.2 for Oracle Solaris 10. [How to restore] Restart the physical partition according to the following steps. 1. Execute the poweroff(8) command to power off the physical partition (PPAR). 2. Execute the poweron(8) command to restart PPAR. |
| Bug | 19680186 19454809 |
| Model | SPARC M12-2S, SPARC M10-4S |
| Description | If Oracle Solaris 11.2 and later is running and the system board is deleted by dynamic reconfiguration of physical partitions (PPAR DR), Oracle Solaris may panic. |
| Workaround | This has been modified with SRU 11.2.10.5.0. Add the following setting to /etc/system of all logical domains, and restart Oracle Solaris: set lgrp_topo_levels=1 Be sure to delete set lgrp_topo_levels=1 in /etc/system before applying SRU 11.2.10.5.0 or later. |
| Bug | 19728345 |
| Model | SPARC M10-4S |
| Description | The physical partition dynamic reconfiguration (PPAR DR) fails if the ldoms/ldmd services are restarted because of Oracle Solaris panic and the like during PPAR DR. |
| Workaround | This has been modified with SRU 11.2.8.4.0 and Oracle VM Server for SPARC 3.2 for Oracle Solaris 10. [How to restore] Hypervisor abort may be caused from the operation of adding/removing memory to/from PPAR DR or a logical domain after the ldoms/ldmd services are recovered. Therefore, execute the poweroff(8) command for XSCF firmware to power off the physical partition (PPAR), then execute the poweron(8) command to power on the PPAR. |
| Bug | 19913088 |
| Model | SPARC M12-1, SPARC M12-2, SPARC M12-2S, SPARC M10-1, SPARC M10-4, SPARC M10-4S |
| Description | If a root complex with PCI expansion unit connected is added dynamically to the logical domain with the ldm add-io command, the logical domain may output the following message, causing Oracle Solaris to panic. panic[cpuX]/thread=XXXXXXXXXXXX: bad stack overflow at TL 1 |
| Workaround | This has been modified with SRU 11.2.10.5.0. Before adding the root complex to the logical domain dynamically, add the following setting to /etc/system, and then restart Oracle Solaris. set default_stksize = 0xa000 |
| Bug | 20061005 19200041 |
| Model | SPARC M10-4S |
| Description | If you use the ipadm(1M) command or the ifconfig(1M) command on the guest domain that has the physical device after you delete the system board dynamically with the deleteboard(8) command, the guest domain may output the following message, causing Oracle Solaris to panic. panic[cpuXX]/thread=XXXXXXXXXXXX: assertion failed: obj->afo_corep == NULL, file: ../../common/os/numaio.c, line: 724 |
| Workaround | This has been modified with SRU 11.2.10.5.0. If you delete the system board dynamically with the deleteboard(8) command, execute the following command before you execute the ipadm(1M) command or the ifconfig(1M) command on the guest domain. # modunload -i 0 |
| Bug | 20458698 |
| Model | SPARC M12-1, SPARC M12-2, SPARC M12-2S, SPARC M10-1, SPARC M10-4, SPARC M10-4S |
| Description | No response time from the migration source domain may become long because a different process from the original live migration is performed during live migration. Network services and the like operating on the migration source domain may time out because of no response. This case occurs if the migration source domain meets both of the following conditions. - The difference between the maximum RA of the migration source domain (actual address) and its minimum RA cannot be divided by 64 MB - The remainder is 32 MB or less when the difference between the maximum RA of the migration source domain and its minimum RA is divided by 64 MB The maximum RA and the minimum RA of the domain can be checked with the following command. [Example] # ldm list-domain -o memory domain-name NAME domain-name MEMORY RA PA SIZE 0x10000000 0x7b0fc0000000 1G minimum RA 0x400800000 0x7f01a0800000 11G (a) (b) The maximum RA is the sum of (a) + (b), which will be 0x6c0800000. 0x400800000 + 0x2c0000000(11G) = 0x6c0800000 The difference between the maximum RA and the minimum RA is 27400 MB. 0x6c0800000 - 0x10000000 = 0x6b0800000 = 27400 MB Therefore, the remainder is 8 MB in this example. 27400 MB / 64 MB = 428 and the remainder is 8 MB |
| Workaround | This has been modified with SRU 11.2.11.5.0. |
| Bug | 20878144 |
| Model | SPARC M12-1, SPARC M12-2, SPARC M12-2S, SPARC M10-1, SPARC M10-4, SPARC M10-4S |
| Description | For Oracle Solaris 11.2 SRU 11.2.8.4.0 or later, "OS Started. No state support" is displayed by the showdomainstatus(8) command or in the event log when Oracle Solaris starts. This message indicates that the status of a logical domain has changed to Oracle Solaris. The following is an example of the message. XSCF> showlogs event Date Message --- Omitted --- Mar 27 15:55:31 ** Event: SCF:PPARID 0 GID 00000000 state change (OpenBoot Running) Mar 27 15:55:32 ** Event: SCF:PPARID 0 GID 00000000 state change (OpenBoot Primary Boot Loader) Mar 27 15:55:33 ** Event: SCF:PPARID 0 GID 00000000 state change (OpenBoot Running OS Boot) Mar 27 15:55:35 ** Event: SCF:PPARID 0 GID 00000000 state change (OS Started. No state support) Mar 27 15:55:36 ** Event: SCF:PPARID 0 GID 00000000 state change (OS Started. No state support) Mar 27 15:56:42 ** Event: SCF:PPARID 0 GID 00000000 state change (Solaris booting) Mar 27 15:57:37 ** Event: SCF:PPARID 0 GID 00000000 state change (Solaris booting) Mar 27 15:57:37 ** Event: SCF:PPARID 0 GID 00000000 state change (Solaris running) XSCF> showdomainstatus -p 0 2015-MM-DD hh:mm:ss Logical Domain Name Status primary OS Started. No state support. |
| Workaround | This has been modified with SRU 11.2.11.5.0. Ignore this message since it does not affect the system operation. |
| Bug | 20974426 |
| Model | SPARC M10-1, SPARC M10-4, SPARC M10-4S |
| Description | In an environment with Oracle VM Server for SPARC 3.2 applied to the control domain and configuration information already saved in the XSCF, if the SPARC M10 system chassis or physical partition (PPAR) is stopped or started, the SPARC M10 system chassis or PPAR may not be able to start with the saved configuration information. This problem occurs when the configuration information is saved by any of the following means: - ldm add-spconfig -r command - Automatic recovery using automatic recovery policy 3 of Oracle VM Server for SPARC ldmd daemon (automatic saving of configuration information) You can check the automatic recovery policy of the ldmd daemon with the following command. The default for the automatic recovery policy is 1 (display warning messages in log files) [Example] # svccfg -s ldmd listprop ldmd/autorecovery_policy ldmd/autorecovery_policy integer 3 |
| Workaround | This has been modified with SRU 11.2.11.5.0. [How to restore] - If the ldm add-spconfig -r command was executed, delete the saved configuration information, and overwrite it by saving the current configuration. [Example] # ldm remove-spconfig CONF-A # ldm add-spconfig CONF-A - If the automatic recovery policy is set to 3, change the automatic recovery policy to 1 by performing the following procedure. [Example] # svccfg -s ldmd setprop ldmd/autorecovery_policy=1 # svcadm refresh ldmd If the SPARC M10 system chassis or PPAR cannot start with the saved configuration information, start the system in the factory-default configuration, and then restore the configuration information already saved in the XML file. |
| Bug | 21106074 |
| Model | SPARC M12-1, SPARC M12-2, SPARC M12-2S, SPARC M10-1, SPARC M10-4, SPARC M10-4S |
| Description | If any of aes-128-ccm, aes-192-ccm, and aes-256-ccm is specified for the encryption algorithm, accessing the ZFS data set with encryption enabled may cause a system panic. The default encryption algorithm is aes-128-ccm. If ZFS is encrypted with no encryption algorithm specified, aes-128-ccm is assumed specified. [Panic message example] panic[cpu34]/thread=2a1053d9c20: bad floating point trap at TL 1 %tl %tpc %tnpc %tstate %tt 1 00000000123eabc0 00000000123eabc4 8880001600 077 %gl: 00 %ccr: 88 %asi: 80 %cwp: 0 %pstate: 16 (Omitted) |
| Workaround | This has been modified with SRU 11.2.12.5.0. Add the following statements to the /etc/system file, and reboot the system. set auxv_cap_exclude_hw1=0x10000 set auxv_cap32_exclude_hw1=0x10000 |
| Bug | 21306352 |
| Model | SPARC M12-2S, SPARC M10-4S |
| Description | The physical partition dynamic reconfiguration (PPAR DR) feature may fail if used to delete a system board in an environment containing a root domain (not a control domain) running Oracle Solaris 11.2 SRU 11.2.9.5.0 or later. [Example] XSCF> deleteboard -y -c disconnect -m unbind=resource 01-0 PSB#01-0 will be unconfigured from PPAR immediately. Continue?[y|n] :y Start unconfigure preparation of PSB. [1200sec] 0.end Unconfigure preparation of PSB has completed. Start unconfiguring PSB from PPAR. [7200sec] 0..... 30..... 60..... 90.....- end Timeout detected during communicate with Logical Domains Manager. XSCF> |
| Workaround | You can avoid this problem by deleting the PCIe bus on the target system board from the domain before the PPAR DR feature deletes the system board. [Example] primary# ldm remove-io PCIE8 domainX : primary# ldm remove-io PCIE15 domainY XSCF> deleteboard -y -c disconnect -m unbind=resource 01-0 [How to restore] After deleting the PCIe bus on the target system board from the domain, re-execute the deleteboard command on the XSCF. [Example] primary# ldm remove-io PCIE8 domainX : primary# ldm remove-io PCIE15 domainY XSCF> deleteboard -y -c disconnect -m unbind=resource 01-0 |
< Previous Page | Next Page >