Skip to main content

Contents

  1. Preface
  2. Chapter 1 Understanding the Installation Flow
    1.  1.1 Workflows for the SPARC M12-2
    2.  1.2 Workflow at Expansion With the PCI Expansion Unit
  3. Chapter 2 Planning and Preparing for System Installation
    1.  2.1 Safety Precautions
    2.  2.2 Items Requiring Confirmation Before Installation
    3. Click 2.3 Confirming the Physical Specifications of the System
    4. Click 2.4 Confirming Rack Specifications
    5. Click 2.5 Checking Environmental Conditions
    6.  2.6 Checking Acoustic Noise Levels
    7.  2.7 Checking Cooling Conditions
    8. Click 2.8 Checking the Power Input Type
    9. Click 2.9 Preparing Power Supply Facilities
    10. Click 2.10 Checking External Interface Port Specifications
    11.  2.11 Checking the Functions of the Operation Panel
  4. Chapter 3 Installing the System
    1.  3.1 Preparing the Necessary Tools/Information for Installation
    2. Click 3.2 Confirming Delivered Components
    3. Click 3.3 Mounting the SPARC M12-2 and the PCI Expansion Unit in a Rack
    4. Click 3.4 Mounting Optional Components
  5. Chapter 4 Connecting Cables to the SPARC M12-2 and the PCI Expansion Unit
    1.  4.1 Connecting Cables to the SPARC M12-2
    2.  4.2 Connecting Cables to the PCI Expansion Unit
    3.  4.3 Storing Cables
  6. Chapter 5 Performing an Initial System Diagnosis
    1.  5.1 Connecting the System Management Terminal
    2.  5.2 Turning On the Input Power and Starting the XSCF
    3.  5.3 Logging In to the XSCF
    4.  5.4 Checking the XCP Firmware Version
    5.  5.5 Checking the Altitude Setting
    6.  5.6 Setting the Time
    7.  5.7 Performing a Diagnosis Test
    8.  5.8 Checking the Component Status
  7. Chapter 6 Making the Initial System Settings
    1.  6.1 Setting the Password Policy
    2.  6.2 Setting a User Account and Password
    3. Click 6.3 Configuring the Telnet/SSH Service
    4.  6.4 Configuring the HTTPS Service
    5. Click 6.5 Configuring the XSCF Network
    6.  6.6 Configuring Memory Mirroring
    7.  6.7 Creating a PPAR Configuration List
    8.  6.8 Checking the Physical Partition (PPAR) Status
    9.  6.9 Synchronizing the Physical Partition (PPAR) Time and XSCF Time
    10. Click 6.10 Registering a CPU Activation Key
    11.  6.11 Assigning CPU Core Resources
    12.  6.12 Starting and Stopping a System (PPAR)
    13.  6.13 Installing Oracle Solaris
    14. Click 6.14 Saving Configuration Information
  8. Appendix A Troubleshooting
    1.  A.1 Understanding the Usual Problems and Their Corrective Actions
    2. Click A.2 Understanding Commands for Troubleshooting
  9. Appendix B Setup Command Workflow
  10. Appendix C Installation Procedure Checklist

2.9.4 Grounding Requirements


2.9.4 Grounding Requirements
Ground the SPARC M12-2 and the PCI expansion unit appropriately according to the input power type.
  1. For single-phase input
    The components of the SPARC M12-2 and PCI expansion unit do not include a grounded (three-wire type) power cord. Order power cords that match the device. Always connect the power cords to grounded power outlets.
    To confirm the type of power supplied in the building, contact the facility administrator or a certified electrician.
  2. For three-phase input
    No power cord is supplied for three-phase input. Grounded power cords must be connected from the distribution panel directly to the terminal boards of the power chassis as part of local electrical work.
    Although common grounding is possible with this device, grounding methods vary depending on the building where the installation is done. When grounding devices using common grounding, make sure that grounding resistance is 10 ohms or less. Be sure to have the facility administrator or a certified electrician confirm the grounding method for the building and perform the grounding work.
    Also, do not connect to a power supply facility of the IT power distribution system where the neutral phase of three phases is not grounded. Otherwise, equipment may malfunction or be damaged.

Top of Page