Skip to main content

Contents

  1. Preface
  2. Chapter 1 Understanding the Installation Flow
    1.  1.1 Workflow for the SPARC M12-1
    2.  1.2 Workflow for Adding the PCI Expansion Unit
  3. Chapter 2 Planning and Preparing for System Installation
    1.  2.1 Safety Precautions
    2.  2.2 Items Requiring Confirmation Before Installation
    3. Click 2.3 Confirming the Physical Specifications of the System
    4. Click 2.4 Confirming Rack Specifications
    5. Click 2.5 Checking Environmental Conditions
    6.  2.6 Checking Acoustic Noise Levels
    7.  2.7 Checking Cooling Conditions
    8. Click 2.8 Checking the Power Input Type
    9. Click 2.9 Preparing Power Supply Facilities
    10. Click 2.10 Checking External Interface Port Specifications
    11.  2.11 Checking the Functions of the Operation Panel
  4. Chapter 3 Installing the System
    1.  3.1 Preparing the Necessary Tools/Information for Installation
    2. Click 3.2 Confirming Delivered Components
    3.  3.3 Confirming the Rack
    4. Click 3.4 Mounting the Chassis in a Rack
    5. Click 3.5 Mounting Optional Components
  5. Chapter 4 Connecting Cables
    1.  4.1 Connecting Cables to the SPARC M12-1
    2.  4.2 Connecting Cables to the PCI Expansion Unit
  6. Chapter 5 Performing an Initial System Diagnosis
    1.  5.1 Connecting the System Management Terminal to the Chassis
    2.  5.2 Turning On the Input Power and Starting the XSCF
    3.  5.3 Logging In to the XSCF
    4.  5.4 Checking the XCP Version
    5.  5.5 Checking the Altitude Setting
    6.  5.6 Setting the Time
    7.  5.7 Performing a Diagnosis Test
    8.  5.8 Checking the Component Status
  7. Chapter 6 Making the Initial System Settings
    1.  6.1 Setting the Password Policy
    2.  6.2 Setting a User Account and Password
    3. Click 6.3 Configuring the Telnet/SSH Service
    4.  6.4 Configuring the HTTPS Service
    5. Click 6.5 Configuring the XSCF Network
    6.  6.6 Configuring Memory Mirroring
    7.  6.7 Creating a PPAR Configuration List
    8.  6.8 Checking the Physical Partition (PPAR) Status
    9.  6.9 Synchronizing the Physical Partition (PPAR) Time and XSCF Time
    10. Click 6.10 Registering a CPU Activation Key
    11.  6.11 Assigning CPU Core Resources
    12.  6.12 Starting/Stopping the System (PPAR)
    13.  6.13 Installing Oracle Solaris
    14. Click 6.14 Saving Configuration Information
  8. Appendix A Troubleshooting
    1.  A.1 Understanding the Usual Problems and Their Corrective Actions
    2. Click A.2 Understanding Commands for Troubleshooting
  9. Appendix B Setup Command Workflow
  10. Appendix C Installation Procedure Checklist

6.5.4 Applying Network Settings


6.5.4 Applying Network Settings
To complete configuration of the network, settings must be reflected and the XSCF must be rebooted. The XSCF reboot disconnects the XSCF session, so log in again.
  1. Execute the applynetwork command on the XSCF shell.
    Executing the command will display network settings. You can confirm that the settings are done.
XSCF> applynetwork
The following network settings will be applied:
bb#00 hostname :scf0-hostname
DNS domain name :example.com

interface :bb#00-lan#0
status :up
IP address :192.168.1.x
netmask :255.255.255.0
route :-n 0.0.0.0 -m 0.0.0.0 -g 192.168.1.1

interface :bb#00-lan#1
status :down
IP address :192.168.2.a
netmask :255.255.255.0
route :-n 0.0.0.0 -m 0.0.0.0 -g 192.168.2.1

  Omitted


Continue? [y|n] :y
Please reset the all XSCFs by rebootxscf to apply the network settings.
Please confirm that the settings have been applied by executing
showhostname, shownetwork, showroute, showsscp and shownameserver after
rebooting the all XSCFs.
  1. Execute the rebootxscf command to reboot the XSCF and complete the settings.
XSCF> rebootxscf -a
The XSCF will be reset. Continue? [y|n] :y
  1. Executing the command will disconnect the XSCF.
    The setting work from this step can be done through an XSCF-LAN connection too.
    To switch from a serial connection to an XSCF-LAN connection, connect to the XSCF by specifying its IP address on a PC connected to the XSCF-LAN, and log in again.
  1. Execute the showhostname, shownetwork, and showroute commands again to display the network settings, and confirm the new network information.

Top of Page