Skip to main content

Contents

  1. Preface
  2. Chapter 1 Understanding the Installation Flow
    1.  1.1 Workflow for the SPARC M12-1
    2.  1.2 Workflow for Adding the PCI Expansion Unit
  3. Chapter 2 Planning and Preparing for System Installation
    1.  2.1 Safety Precautions
    2.  2.2 Items Requiring Confirmation Before Installation
    3. Click 2.3 Confirming the Physical Specifications of the System
    4. Click 2.4 Confirming Rack Specifications
    5. Click 2.5 Checking Environmental Conditions
    6.  2.6 Checking Acoustic Noise Levels
    7.  2.7 Checking Cooling Conditions
    8. Click 2.8 Checking the Power Input Type
    9. Click 2.9 Preparing Power Supply Facilities
    10. Click 2.10 Checking External Interface Port Specifications
    11.  2.11 Checking the Functions of the Operation Panel
  4. Chapter 3 Installing the System
    1.  3.1 Preparing the Necessary Tools/Information for Installation
    2. Click 3.2 Confirming Delivered Components
    3.  3.3 Confirming the Rack
    4. Click 3.4 Mounting the Chassis in a Rack
    5. Click 3.5 Mounting Optional Components
  5. Chapter 4 Connecting Cables
    1.  4.1 Connecting Cables to the SPARC M12-1
    2.  4.2 Connecting Cables to the PCI Expansion Unit
  6. Chapter 5 Performing an Initial System Diagnosis
    1.  5.1 Connecting the System Management Terminal to the Chassis
    2.  5.2 Turning On the Input Power and Starting the XSCF
    3.  5.3 Logging In to the XSCF
    4.  5.4 Checking the XCP Version
    5.  5.5 Checking the Altitude Setting
    6.  5.6 Setting the Time
    7.  5.7 Performing a Diagnosis Test
    8.  5.8 Checking the Component Status
  7. Chapter 6 Making the Initial System Settings
    1.  6.1 Setting the Password Policy
    2.  6.2 Setting a User Account and Password
    3. Click 6.3 Configuring the Telnet/SSH Service
    4.  6.4 Configuring the HTTPS Service
    5. Click 6.5 Configuring the XSCF Network
    6.  6.6 Configuring Memory Mirroring
    7.  6.7 Creating a PPAR Configuration List
    8.  6.8 Checking the Physical Partition (PPAR) Status
    9.  6.9 Synchronizing the Physical Partition (PPAR) Time and XSCF Time
    10. Click 6.10 Registering a CPU Activation Key
    11.  6.11 Assigning CPU Core Resources
    12.  6.12 Starting/Stopping the System (PPAR)
    13.  6.13 Installing Oracle Solaris
    14. Click 6.14 Saving Configuration Information
  8. Appendix A Troubleshooting
    1.  A.1 Understanding the Usual Problems and Their Corrective Actions
    2. Click A.2 Understanding Commands for Troubleshooting
  9. Appendix B Setup Command Workflow
  10. Appendix C Installation Procedure Checklist

5.5 Checking the Altitude Setting


5.5 Checking the Altitude Setting
This section describes the procedure for checking and setting the altitude of the installation location.
The setting in the factory default settings is 0 m. Check the setting value, and change it as needed.
Note - Setting the altitude in the system makes it possible to detect abnormal intake temperatures early. If the altitude of the installation location is unknown, set a high altitude. Abnormal temperatures can be detected from abnormal CPU temperatures, for example, even if no altitude is set in the system. This prevents critical damage to the system.
  1. Execute the showaltitude command.
    The following example displays the system altitude. The factory default setting is 0 m.
XSCF> showaltitude
0m
  1. If the altitude setting is correct, skip step 2 and subsequent steps. To change the altitude, execute the setaltitude command.
    The setting is in units of 100 m, and values less than 100 m are rounded up.
    The following example sets the altitude to 100 m.
XSCF> setaltitude -s altitude=100
100m
  1. Execute the rebootxscf command to reflect the setting.
    If you are also changing the setting values described in "5.6 Setting the Time," you can skip step 3 and subsequent steps because the XSCF is rebooted.
    Executing the rebootxscf command disconnects the XSCF session.
    The following example reboots all the XSCFs and automatically selects "y" for the confirmation message.
XSCF> rebootxscf -y -a
The XSCF will be reset. Continue? [y|n] :y
  1. Log in to the XSCF again.
    For details, see "5.3 Logging In to the XSCF."

Top of Page