Skip to main content
  1. Home >
  2. Products >
  3. Computing Products >
  4. Servers >
  5. Fujitsu SPARC servers >
  6. Downloads >
  7. User Manuals >
  8. Fujitsu SPARC M12-1 Installation Guide >
  9. 2.4.2 Installation Area for a General Rack

Contents

  1. Preface
  2. Chapter 1 Understanding the Installation Flow
    1.  1.1 Workflow for the SPARC M12-1
    2.  1.2 Workflow for Adding the PCI Expansion Unit
  3. Chapter 2 Planning and Preparing for System Installation
    1.  2.1 Safety Precautions
    2.  2.2 Items Requiring Confirmation Before Installation
    3. Click 2.3 Confirming the Physical Specifications of the System
    4. Click 2.4 Confirming Rack Specifications
    5. Click 2.5 Checking Environmental Conditions
    6.  2.6 Checking Acoustic Noise Levels
    7.  2.7 Checking Cooling Conditions
    8. Click 2.8 Checking the Power Input Type
    9. Click 2.9 Preparing Power Supply Facilities
    10. Click 2.10 Checking External Interface Port Specifications
    11.  2.11 Checking the Functions of the Operation Panel
  4. Chapter 3 Installing the System
    1.  3.1 Preparing the Necessary Tools/Information for Installation
    2. Click 3.2 Confirming Delivered Components
    3.  3.3 Confirming the Rack
    4. Click 3.4 Mounting the Chassis in a Rack
    5. Click 3.5 Mounting Optional Components
  5. Chapter 4 Connecting Cables
    1.  4.1 Connecting Cables to the SPARC M12-1
    2.  4.2 Connecting Cables to the PCI Expansion Unit
  6. Chapter 5 Performing an Initial System Diagnosis
    1.  5.1 Connecting the System Management Terminal to the Chassis
    2.  5.2 Turning On the Input Power and Starting the XSCF
    3.  5.3 Logging In to the XSCF
    4.  5.4 Checking the XCP Version
    5.  5.5 Checking the Altitude Setting
    6.  5.6 Setting the Time
    7.  5.7 Performing a Diagnosis Test
    8.  5.8 Checking the Component Status
  7. Chapter 6 Making the Initial System Settings
    1.  6.1 Setting the Password Policy
    2.  6.2 Setting a User Account and Password
    3. Click 6.3 Configuring the Telnet/SSH Service
    4.  6.4 Configuring the HTTPS Service
    5. Click 6.5 Configuring the XSCF Network
    6.  6.6 Configuring Memory Mirroring
    7.  6.7 Creating a PPAR Configuration List
    8.  6.8 Checking the Physical Partition (PPAR) Status
    9.  6.9 Synchronizing the Physical Partition (PPAR) Time and XSCF Time
    10. Click 6.10 Registering a CPU Activation Key
    11.  6.11 Assigning CPU Core Resources
    12.  6.12 Starting/Stopping the System (PPAR)
    13.  6.13 Installing Oracle Solaris
    14. Click 6.14 Saving Configuration Information
  8. Appendix A Troubleshooting
    1.  A.1 Understanding the Usual Problems and Their Corrective Actions
    2. Click A.2 Understanding Commands for Troubleshooting
  9. Appendix B Setup Command Workflow
  10. Appendix C Installation Procedure Checklist

2.4.2 Installation Area for a General Rack


2.4.2 Installation Area for a General Rack
Service areas
Service area requirements vary depending on the rack used.
When mounting each chassis in the designated rack, see the examples of service areas in Figure 2-3 and Figure 2-5. The rack width depends on the rack used.
When using a rack other than the designated rack, see the manual for the rack used.
Figure 2-3  Example of Service Areas for the SPARC M12-1 (Top View)
Figure 2-3 Example of Service Areas for the SPARC M12-1 (Top View)
*1 This area is required on either the left or right side.
*2 To mount a chassis on the rack, an area with a depth of 1,200 mm (47.2 in.) is required in front of the rack.
If there is a possibility that a chassis will be added later, secure an area with a depth of 1,200 mm (47.2 in.) in front of the rack.
Figure 2-4  Example of Service Areas for the SPARC M12-1 When Using a Stepladder (Top View)
Figure 2-4 Example of Service Areas for the SPARC M12-1 When Using a Stepladder (Top View)
*1 This area is required for using a stepladder, and it differs depending on the stepladder used. Referring to the above figure, ensure that the service area is appropriate to the stepladder used. This area is required on either the left or right side.
*2 To mount a chassis in the rack, an area with a depth of 1,200 mm (47.2 in.) is required in front of the rack.
If there is a possibility that a chassis will be added later, secure an area with a depth of 1,200 mm (47.2 in.) in front of the rack.
Figure 2-5  Example of Service Areas for the PCI Expansion Unit (Top View)
Figure 2-5 Example of Service Areas for the PCI Expansion Unit (Top View)
*1 To mount a chassis in the rack, an area with a depth of 1,200 mm (47.2 in.) is required in front of the rack, and areas with a width of 600 mm (23.6 in.) are required on both the left and right sides of the front service area. If there is a possibility that a chassis will be added later, secure an area with a depth of 1,200 mm (47.2 in.) in front of the rack and areas with a width of 600 mm (23.6 in.) on both the left and right sides of the front service area.

Top of Page