Skip to main content
  1. Home >
  2. Products >
  3. Computing Products >
  4. Servers >
  5. Fujitsu SPARC servers >
  6. Downloads >
  7. User Manuals >
  8. Fujitsu SPARC M12-1 Installation Guide >
  9. 5.2 Turning On the Input Power and Starting the XSCF

Contents

  1. Preface
  2. Chapter 1 Understanding the Installation Flow
    1.  1.1 Workflow for the SPARC M12-1
    2.  1.2 Workflow for Adding the PCI Expansion Unit
  3. Chapter 2 Planning and Preparing for System Installation
    1.  2.1 Safety Precautions
    2.  2.2 Items Requiring Confirmation Before Installation
    3. Click 2.3 Confirming the Physical Specifications of the System
    4. Click 2.4 Confirming Rack Specifications
    5. Click 2.5 Checking Environmental Conditions
    6.  2.6 Checking Acoustic Noise Levels
    7.  2.7 Checking Cooling Conditions
    8. Click 2.8 Checking the Power Input Type
    9. Click 2.9 Preparing Power Supply Facilities
    10. Click 2.10 Checking External Interface Port Specifications
    11.  2.11 Checking the Functions of the Operation Panel
  4. Chapter 3 Installing the System
    1.  3.1 Preparing the Necessary Tools/Information for Installation
    2. Click 3.2 Confirming Delivered Components
    3.  3.3 Confirming the Rack
    4. Click 3.4 Mounting the Chassis in a Rack
    5. Click 3.5 Mounting Optional Components
  5. Chapter 4 Connecting Cables
    1.  4.1 Connecting Cables to the SPARC M12-1
    2.  4.2 Connecting Cables to the PCI Expansion Unit
  6. Chapter 5 Performing an Initial System Diagnosis
    1.  5.1 Connecting the System Management Terminal to the Chassis
    2.  5.2 Turning On the Input Power and Starting the XSCF
    3.  5.3 Logging In to the XSCF
    4.  5.4 Checking the XCP Version
    5.  5.5 Checking the Altitude Setting
    6.  5.6 Setting the Time
    7.  5.7 Performing a Diagnosis Test
    8.  5.8 Checking the Component Status
  7. Chapter 6 Making the Initial System Settings
    1.  6.1 Setting the Password Policy
    2.  6.2 Setting a User Account and Password
    3. Click 6.3 Configuring the Telnet/SSH Service
    4.  6.4 Configuring the HTTPS Service
    5. Click 6.5 Configuring the XSCF Network
    6.  6.6 Configuring Memory Mirroring
    7.  6.7 Creating a PPAR Configuration List
    8.  6.8 Checking the Physical Partition (PPAR) Status
    9.  6.9 Synchronizing the Physical Partition (PPAR) Time and XSCF Time
    10. Click 6.10 Registering a CPU Activation Key
    11.  6.11 Assigning CPU Core Resources
    12.  6.12 Starting/Stopping the System (PPAR)
    13.  6.13 Installing Oracle Solaris
    14. Click 6.14 Saving Configuration Information
  8. Appendix A Troubleshooting
    1.  A.1 Understanding the Usual Problems and Their Corrective Actions
    2. Click A.2 Understanding Commands for Troubleshooting
  9. Appendix B Setup Command Workflow
  10. Appendix C Installation Procedure Checklist

5.2 Turning On the Input Power and Starting the XSCF


5.2 Turning On the Input Power and Starting the XSCF
This section describes the procedures for connecting the power cords to outlets, turning on the input power, and starting the XSCF.
  1. Set the mode switch on the operation panel to the Service position.
    The Service position is indicated by a wrench icon. The Locked position is indicated by a lock icon.
Figure 5-1  Mode Switch on the Operation Panel of the SPARC M12-1
Figure 5-1 Mode Switch on the Operation Panel of the SPARC M12-1
  1. Confirm that the power cord connector is connected, all the way straight in, to a power supply unit of the chassis.
    For details, see "4.1 Connecting Cables to the SPARC M12-1."
  2. Connect the power cord plug to an outlet.
    If the outlet has a circuit breaker, turn on the circuit breaker switch.
  3. Check the XSCF unit LEDs.
    a. The CHECK LED of the XSCF unit goes on for an instant immediately after the input power is turned on.

    b. The READY LED of the XSCF unit flashes during XSCF initialization and stays on after the initialization completes.
Figure 5-2  Rear of the SPARC M12-1
Figure 5-2 Rear of the SPARC M12-1

Top of Page