Skip to main content
  1. Home >
  2. Products >
  3. Computing Products >
  4. Servers >
  5. Fujitsu SPARC servers >
  6. Downloads >
  7. User Manuals >
  8. Fujitsu M10-4/SPARC M10-4 Installation Guide >
  9. 2.11 Checking the Functions of the Operation Panel

Contents

  1. Preface
  2. Chapter 1 Understanding the Installation Flow
    1.  1.1 Workflow for the SPARC M10-4
    2. Click 1.2 Workflow When Installing the PCI Expansion Unit
  3. Chapter 2 Planning and Preparing for System Installation
    1.  2.1 Safety Precautions
    2.  2.2 Items Requiring Confirmation before Installation
    3. Click 2.3 Confirming the Physical Specifications of the System
    4. Click 2.4 Confirming Rack Specifications
    5. Click 2.5 Checking Environmental Conditions
    6.  2.6 Checking Acoustic Noise Levels
    7.  2.7 Checking Cooling Conditions
    8. Click 2.8 Checking the Power Input Type
    9. Click 2.9 Preparing Power Supply Facilities
    10. Click 2.10 Checking External Interface Port Specifications
    11.  2.11 Checking the Functions of the Operation Panel
  4. Chapter 3 Installing the System
    1.  3.1 Preparing the Necessary Tools/Information for Installation
    2. Click 3.2 Confirming Delivered Components
    3. Click 3.3 Mounting the Chassis in a Rack
    4. Click 3.4 Mounting Optional Components
  5. Chapter 4 Connecting Cables to the Chassis
    1.  4.1 Connecting Cables to the SPARC M10-4
    2.  4.2 Connecting Cables to the PCI Expansion Unit
  6. Chapter 5 Performing an Initial System Diagnosis
    1.  5.1 Connecting the System Management Terminal to the Chassis
    2.  5.2 Turning on the Input Power and Starting the XSCF
    3.  5.3 Logging In to the XSCF
    4.  5.4 Checking the XCP Version
    5.  5.5 Checking the Altitude Setting
    6.  5.6 Checking the Time Setting
    7.  5.7 Performing a Diagnosis Test
    8.  5.8 Checking the Component Status
  7. Chapter 6 Making the Initial System Settings
    1.  6.1 Setting the Password Policy
    2.  6.2 Setting a User Account and Password
    3. Click 6.3 Configuring the Telnet/SSH Service
    4.  6.4 Configuring the HTTPS Service
    5. Click 6.5 Configuring the XSCF Network
    6.  6.6 Configuring Memory Mirroring
    7.  6.7 Creating a Physical Partition Configuration List (PCL)
    8.  6.8 Confirming That a System Board (PSB) is Assigned to a Physical Partition (PPAR)
    9.  6.9 Setting a CPU Operational Mode for the Physical Partition
    10.  6.10 Synchronizing the Physical Partition (PPAR) Time and XSCF Time
    11. Click 6.11 Registering a CPU Activation Key
    12.  6.12 Assigning CPU Core Resources
    13.  6.13 Starting and Stopping a Physical Partition (PPAR)
    14. Click 6.14 Saving Configuration Information
  8. Appendix A Troubleshooting
    1.  A.1 Understanding the Usual Problems and Their Corrective Actions
    2. Click A.2 Understanding Commands for Troubleshooting
  9. Appendix B Setup Command Workflow
  10. Appendix C Installation Procedure Checklist

2.11 Checking the Functions of the Operation Panel


2.11 Checking the Functions of the Operation Panel
This section describes the functions of the operation panel mounted on the SPARC M10-4.
You can check system operation with the system display (LEDs) and operation functions on the operation panel.
Figure 2-14 shows the SPARC M10-4 operation panel, and Table 2-13 shows the LEDs and switches on the operation panel.
For details on system operations not covered in the functional outline of Table 2-13, see "2.3 Confirming the Functions of the Operation Panel" in the Fujitsu M10-4/Fujitsu M10-4S/SPARC M10-4/SPARC M10-4S Service Manual.
Figure 2-14  SPARC M10-4 operation panel
Figure 2-14 SPARC M10-4 operation panel
Table 2-13  LEDs and switches on the operation panel
No. LED/Switch Functional outline
1 POWER LED Indicates the operating status of the system.
 On: The system is running.
 Off: The system is stopped.
 Blinking: The system is being stopped.
2 XSCF STANDBY LED Indicates the XSCF status of the system.
 On: The XSCF is running.
 Off: The XSCF is stopped.
 Blinking: The XSCF is being started.
3 CHECK LED Indicates whether the SPARC M10-4 is in an abnormal state.
 Off: Normal, or no power being supplied
 On: Hardware has detected an error.
4 Mode switch Sets the system operation mode.
5 POWER switch Starts/Stops the system.
You can perform the following operations with the switches shown at (4) and (5) in Table 2-13.

  1. Mode switch
    This switch sets the start mode for the system. You can switch between Locked mode and Service mode on the mode switch by sliding the switch.

    - Locked mode (locked_mode )
    This mode is used during normal operation.
    You can turn on the power but cannot turn off the power with the POWER switch. This mechanism disables power-off in order to prevent users from turning off the power by mistake.

    - Service mode (service_mode )
    This mode is used during maintenance work.
    You can turn off the power with the POWER switch, but the switch is inhibited from turning on the power. Maintenance with the whole system stopped is performed in Service mode.

  2. POWER switch
    You can start or stop the system.
    The operation to start or stop the system depends on how the POWER switch is pressed and the setting of the system mode switch.

Top of Page