Skip to main content

Contents

  1. Preface
  2. Chapter 1 Understanding the Installation Flow
    1.  1.1 Workflow for the SPARC M10-4
    2. Click 1.2 Workflow When Installing the PCI Expansion Unit
  3. Chapter 2 Planning and Preparing for System Installation
    1.  2.1 Safety Precautions
    2.  2.2 Items Requiring Confirmation before Installation
    3. Click 2.3 Confirming the Physical Specifications of the System
    4. Click 2.4 Confirming Rack Specifications
    5. Click 2.5 Checking Environmental Conditions
    6.  2.6 Checking Acoustic Noise Levels
    7.  2.7 Checking Cooling Conditions
    8. Click 2.8 Checking the Power Input Type
    9. Click 2.9 Preparing Power Supply Facilities
    10. Click 2.10 Checking External Interface Port Specifications
    11.  2.11 Checking the Functions of the Operation Panel
  4. Chapter 3 Installing the System
    1.  3.1 Preparing the Necessary Tools/Information for Installation
    2. Click 3.2 Confirming Delivered Components
    3. Click 3.3 Mounting the Chassis in a Rack
    4. Click 3.4 Mounting Optional Components
  5. Chapter 4 Connecting Cables to the Chassis
    1.  4.1 Connecting Cables to the SPARC M10-4
    2.  4.2 Connecting Cables to the PCI Expansion Unit
  6. Chapter 5 Performing an Initial System Diagnosis
    1.  5.1 Connecting the System Management Terminal to the Chassis
    2.  5.2 Turning on the Input Power and Starting the XSCF
    3.  5.3 Logging In to the XSCF
    4.  5.4 Checking the XCP Version
    5.  5.5 Checking the Altitude Setting
    6.  5.6 Checking the Time Setting
    7.  5.7 Performing a Diagnosis Test
    8.  5.8 Checking the Component Status
  7. Chapter 6 Making the Initial System Settings
    1.  6.1 Setting the Password Policy
    2.  6.2 Setting a User Account and Password
    3. Click 6.3 Configuring the Telnet/SSH Service
    4.  6.4 Configuring the HTTPS Service
    5. Click 6.5 Configuring the XSCF Network
    6.  6.6 Configuring Memory Mirroring
    7.  6.7 Creating a Physical Partition Configuration List (PCL)
    8.  6.8 Confirming That a System Board (PSB) is Assigned to a Physical Partition (PPAR)
    9.  6.9 Setting a CPU Operational Mode for the Physical Partition
    10.  6.10 Synchronizing the Physical Partition (PPAR) Time and XSCF Time
    11. Click 6.11 Registering a CPU Activation Key
    12.  6.12 Assigning CPU Core Resources
    13.  6.13 Starting and Stopping a Physical Partition (PPAR)
    14. Click 6.14 Saving Configuration Information
  8. Appendix A Troubleshooting
    1.  A.1 Understanding the Usual Problems and Their Corrective Actions
    2. Click A.2 Understanding Commands for Troubleshooting
  9. Appendix B Setup Command Workflow
  10. Appendix C Installation Procedure Checklist

2.5.3 Contaminant conditions


2.5.3 Contaminant conditions
Table 2-5 provides the acceptable reference values for contaminants with regard to the SPARC M10 systems.
Table 2-5  Acceptable reference values for contaminants
Contaminant Acceptable reference value
Hydrogen sulfide (H2S) 7.1 ppb or less
Sulfurous acid gas (sulfur oxide) (SO2)
37 ppb or less
Hydrogen chloride (HCI) 6.6 ppb or less
Chlorine (CI2) 3.4 ppb or less
Hydrogen fluoride (HF) 3.6 ppb or less
Nitrogen dioxide (nitrogen oxide) (NO2)
52 ppb or less
Ammonia (NH3)
420 ppb or less
Ozone (O3)
5 ppb or less
Oil vapor 0.2 mg/m3 or less
Dust 0.15 mg/m3 or less
Seawater (salt damage) Do not install out at sea or within 500 m (1,640.4 ft.) of the seashore.
(However, this does not apply if air conditioning facilities do not use outside air.)

Top of Page