Skip to main content

Contents

  1. Preface
  2. Chapter 1 Understanding the Installation Flow
    1.  1.1 Workflow for the SPARC M10-4
    2. Click 1.2 Workflow When Installing the PCI Expansion Unit
  3. Chapter 2 Planning and Preparing for System Installation
    1.  2.1 Safety Precautions
    2.  2.2 Items Requiring Confirmation before Installation
    3. Click 2.3 Confirming the Physical Specifications of the System
    4. Click 2.4 Confirming Rack Specifications
    5. Click 2.5 Checking Environmental Conditions
    6.  2.6 Checking Acoustic Noise Levels
    7.  2.7 Checking Cooling Conditions
    8. Click 2.8 Checking the Power Input Type
    9. Click 2.9 Preparing Power Supply Facilities
    10. Click 2.10 Checking External Interface Port Specifications
    11.  2.11 Checking the Functions of the Operation Panel
  4. Chapter 3 Installing the System
    1.  3.1 Preparing the Necessary Tools/Information for Installation
    2. Click 3.2 Confirming Delivered Components
    3. Click 3.3 Mounting the Chassis in a Rack
    4. Click 3.4 Mounting Optional Components
  5. Chapter 4 Connecting Cables to the Chassis
    1.  4.1 Connecting Cables to the SPARC M10-4
    2.  4.2 Connecting Cables to the PCI Expansion Unit
  6. Chapter 5 Performing an Initial System Diagnosis
    1.  5.1 Connecting the System Management Terminal to the Chassis
    2.  5.2 Turning on the Input Power and Starting the XSCF
    3.  5.3 Logging In to the XSCF
    4.  5.4 Checking the XCP Version
    5.  5.5 Checking the Altitude Setting
    6.  5.6 Checking the Time Setting
    7.  5.7 Performing a Diagnosis Test
    8.  5.8 Checking the Component Status
  7. Chapter 6 Making the Initial System Settings
    1.  6.1 Setting the Password Policy
    2.  6.2 Setting a User Account and Password
    3. Click 6.3 Configuring the Telnet/SSH Service
    4.  6.4 Configuring the HTTPS Service
    5. Click 6.5 Configuring the XSCF Network
    6.  6.6 Configuring Memory Mirroring
    7.  6.7 Creating a Physical Partition Configuration List (PCL)
    8.  6.8 Confirming That a System Board (PSB) is Assigned to a Physical Partition (PPAR)
    9.  6.9 Setting a CPU Operational Mode for the Physical Partition
    10.  6.10 Synchronizing the Physical Partition (PPAR) Time and XSCF Time
    11. Click 6.11 Registering a CPU Activation Key
    12.  6.12 Assigning CPU Core Resources
    13.  6.13 Starting and Stopping a Physical Partition (PPAR)
    14. Click 6.14 Saving Configuration Information
  8. Appendix A Troubleshooting
    1.  A.1 Understanding the Usual Problems and Their Corrective Actions
    2. Click A.2 Understanding Commands for Troubleshooting
  9. Appendix B Setup Command Workflow
  10. Appendix C Installation Procedure Checklist

3.3.1 Mounting the SPARC M10-4 in a rack


3.3.1 Mounting the SPARC M10-4 in a rack
  1. Confirm that the rack mount kit supplied with the SPARC M10-4 is complete.
Note - The rack mount kit contains two types of cable support: Type-1 and Type-2. The Type-2 cable support is an integrated unit consisting of the parts indicated by numbers 2 to 5 in Figure 3-1. Steps 7 and 11 in the mounting procedure vary depending on the shape of the cable support. Attach the support according to the corresponding steps.
Figure 3-1  Rack mount kit
Figure 3-1 Rack mount kit
Number in figure Name Quantity Remarks
1 Rail 2 Bilaterally symmetrical shape
2 Cable support (*1) (*2) 1  
3 Cable support bracket (*2) 2 Bilaterally symmetrical shape
4 M3 screw (*2) 2  
5 Cable support fixing bracket (*2) 2 Bilaterally symmetrical shape
6 M6 screw 10  
7 Cage nut 10  
*1 There are two types of cable support: Type-1 and Type-2. To distinguish between them, see Figure 3-2.
*2 The Type-2 cable support is an integrated unit consisting of these parts.
Figure 3-2  Type-2 cable support
Figure 3-2 Type-2 cable support
  1. Confirm that the rack is fixed in place to prevent the rack from toppling over.
  2. Confirm the chassis mounting location in the rack. If necessary, mark the location on the supporting columns.
  3. Step 4 differs depending on the shape of the supporting column holes of the rack. Perform the work appropriate to the shape of the supporting column holes of the rack.
  1. For racks with supporting columns having square holes
  1. Attach cage nuts to the left and right supporting columns of the rack.
    - Attachment locations in the front supporting columns: (From the bottom) 1U center, 2U bottom, and 3U top

    - Attachment locations in the rear supporting columns: (From the bottom) 1U center and 2U center
Figure 3-3  Cage nut attachment locations in the supporting columns of the rack
Figure 3-3 Cage nut attachment locations in the supporting columns of the rack
  1. a. Attach cage nuts from the inside of the rack.
    Orient the hooks of the cage nut vertically.
    Hook the hook at one end of a cage nut into a cage nut attachment hole of the rack.
    Figure 3-4 shows a cage nut hooked on the lower part of a hole.
Figure 3-4  Orientation of the hooks of a cage nut
Figure 3-4 Orientation of the hooks of a cage nut
  1. b. Insert the hook at the tip of the supplied cage nut attachment tool through a cage nut attachment hole from the front, and engage it with the hook at the other end of the cage nut.
Figure 3-5  Using the cage nut attachment tool
Figure 3-5 Using the cage nut attachment tool
  1. c. Pull the tool forward to attach the cage nut.
    Push in direction A while simultaneously pulling in direction B as shown in Figure 3-6.
Figure 3-6  Attaching a cage nut
Figure 3-6 Attaching a cage nut
  1. For supporting columns with M6 screw holes
  1. Remove the pins at the front and rear of the rail.
    a. Remove the screw (A in Figure 3-7) securing the rail pin.

    b. Remove the pin (B in Figure 3-7).

    c. Remove pins from the left and right rails in the same manner.

    d. Store the removed pins and screws (eight pins and eight screws in total) for future use when the chassis is moved.
Figure 3-7  Removing a rail pin
Figure 3-7 Removing a rail pin
  1. Remove the one screw (A in Figure 3-8) from the side of the rail.
    The removed screw will be used in step 8.
Figure 3-8  Screws on the sides of rails
Figure 3-8 Screws on the sides of rails
  1. Attach the rail to the rack.
    Attach the rail such that the spring-loaded side (B in Figure 3-8) faces the front and the flange (C in Figure 3-8) faces the bottom.
    a. From the front of the rack, insert the rail protrusions into 2U top and 1U top in the front supporting column of the rack.

    b. Pull out the rail to as far as the depth of the rack.

    c. Insert the rail protrusions into 2U top and 1U bottom in the rear supporting column of the rack.

    d. Secure the rail with one M6 screw to the front supporting column of the rack. The fixing location is 2U bottom.

    e. Attach the other rail in the same manner.
Note - After removing its screw, hold the rail level with both hands. If the rail tilts, it may stretch.
Figure 3-9  Attaching the rail: Locations of protrusions
Figure 3-9 Attaching the rail: Locations of protrusions
Figure 3-10  Attaching the rail: Fixing location of the screw
Figure 3-10 Attaching the rail: Fixing location of the screw
  1. Attach the cable support fixing brackets to the rear supporting columns of the rack.
  1. For the Type-1 cable support
    a. Orient the notches (B in Figure 3-11) on the cable support fixing brackets (A in Figure 3-11) face down.

    b. From the rear of the rack, secure the rails and cable support brackets with two M6 screws to the rear supporting columns of the rack.

     The fixing locations are 1U center and 2U center.

    c. After attaching the cable support bracket, confirm that the rack door can close.
Note - If the door cannot close because the cable support fixing bracket or the cable support protrudes from the rear of the rack, do not attach the cable support bracket. However, secure the rail to the rack with two M6 screws.
Figure 3-11  Attaching the cable support fixing bracket
Figure 3-11 Attaching the cable support fixing bracket
Figure 3-12  Securing the cable support fixing brackets and the rails
Figure 3-12 Securing the cable support fixing brackets and the rails
  1. For the Type-2 cable support
    a. Loosen the four screws (C in Figure 3-13) from the inside of the cable support.


Figure 3-13  Removing the cable support fixing brackets (1)
Figure 3-13 Removing the cable support fixing brackets (1)
  1. b. Slide the cable support fixing brackets (D in Figure 3-14) to remove them.
Figure 3-14  Removing the cable support fixing brackets (2)
Figure 3-14 Removing the cable support fixing brackets (2)
  1. c. From the rear of the rack, secure the rails and cable support fixing brackets (D) with two M6 screws to the rear supporting columns of the rack.

    The fixing locations are 1U center and 2U center.
Figure 3-15  Attaching the cable support brackets
Figure 3-15 Attaching the cable support brackets
Figure 3-16  Securing the cable support fixing brackets and the rails
Figure 3-16 Securing the cable support fixing brackets and the rails
  1. d. After attaching the cable support fixing brackets, confirm that the rack door can close.
Note - If the door cannot close because the cable support fixing bracket or the cable support protrudes from the rear of the rack, do not attach the cable support bracket. However, secure the rail to the rack with two M6 screws.
  1. Secure the rail sides by using the screws (M5) removed in step 5 (A in Figure 3-17).
Figure 3-17  Securing the sides of rails with screws
Figure 3-17 Securing the sides of rails with screws
  1. Mount the chassis in the rack.
    Mount the chassis from the front of the rack.
Note - The SPARC M10-4 weighs 60 kg. Mount the chassis in the rack with four or more people working together. Alternatively, use a lifter such as a hydraulic or mechanical jack.
  1. a. When using a lifter, secure it horizontally.

    b. Lift the chassis to the mounting location with the lifter or with human force.

    c. Put the rear part of the chassis on the flanges of the rails.

    d. Slide the chassis into the rack. At this time, store the handle on the side of the chassis. Also, confirm that the guide pins of the chassis (A in Figure 3-18) fit into their rail guides (B in Figure 3-18).

    e. Insert the chassis all the way to store it inside the rack.
Figure 3-18  Mounting in the rack
Figure 3-18 Mounting in the rack
  1. Secure the chassis to the rack.
    a. Push out the left and right slide locks on the front cover (C in Figure 3-18) to release the locks, and remove the front cover.

    b. Tighten the four M6 screws at four locations on the front of the chassis (A in Figure 3-19) to secure it to the rack.

    c. Insert the left and right hooks on the inside of the bottom of the front cover into the grooves at the bottom front of the chassis to attach the front cover.
Note - A label with the serial number of the chassis is affixed to the front cover. Be sure to attach the front cover to the corresponding chassis.
Figure 3-19  Securing the chassis
Figure 3-19 Securing the chassis
  1. Attach the cable support.
  1. For the Type-1 cable support
    a. From the inside of the cable support fixing bracket, align the two screws in the right cable support bracket with the circular holes at the front of the groove, and attach the screws (A in Figure 3-20).

    b. Slide the cable support bracket toward the chassis while holding the latch (B in Figure 3-20) attached to it.

    c. Attach the left cable support bracket in the same manner.
    At this time, the left and right sides should have been slid the same amount (depth) toward the chassis.

    d. Secure the cable support with two M3 screws (C in Figure 3-21).

    e. Close the rear door of the rack, and confirm that the cable support does not interfere. If it interferes, slide the cable support toward the chassis while holding the latches (B in Figure 3-20) of the left and right cable support brackets. The cable support should be in the position nearest the chassis, with the cable support bracket latches engaged.

    f. If the cable support interferes with the door even when you slide it toward the chassis as far as possible, remove the cable support.


Figure 3-20  Attaching the cable support brackets
Figure 3-20 Attaching the cable support brackets
Figure 3-21  Attaching the cable support
Figure 3-21 Attaching the cable support
  1. For the Type-2 cable support
    a. Tilt the cable support to align the circular holes at the rear of the groove with the two screws of a cable support fixing bracket (D in Figure 3-22), and attach it. Level the cable support. Then, align the circular holes at the other side with the two screws, and attach it.


Figure 3-22  Attaching the cable support (1)
Figure 3-22 Attaching the cable support (1)
  1. b. Slide in the cable support all the way, and tighten the four screws (C in Figure 3-23).
Figure 3-23  Attaching the cable support (2)
Figure 3-23 Attaching the cable support (2)
Note - If the dimension between the front and rear columns of the rack is less than 740 mm, secure the cable support without sliding it in all the way. The fixing location varies depending on the dimension between the front and rear columns of the rack. Based on Figure 3-24, align the scale marks (E in Figure 3-24) (spacing: 10 mm) on the cable support with the screws (F in Figure 3-24) of the fixing brackets to secure the cable support.
Figure 3-24  Attaching the cable support (3)
Figure 3-24 Attaching the cable support (3)
Table 3-4  Dimensions between the front and rear columns and scale positions
Dimension between front and rear columns (mm) Scale position
740 1st
730 2nd
720 3rd
710 4th
700 5th
690 6th
680 7th
670 8th
660 9th
650 10th
Note - If you have difficulty laying a thick cable into the cable support, move forward the fixing location of the cable support to make the work easier.
  1. c. Close the rear door of the rack, and confirm that the cable support does not interfere. If the cable support interferes with the rear door, remove the cable support. Even if you remove the cable support, leave the rails secured with the two M6 screws to the rack.
Figure 3-25  Completed SPARC M10-4 configuration
Figure 3-25 Completed SPARC M10-4 configuration

Top of Page