Skip to main content

Contents

  1. Preface
  2. Chapter 1 Understanding the Installation Flow
    1.  1.1 Workflow for the SPARC M10-1
    2. Click 1.2 Workflow for Installing the PCI Expansion Unit
  3. Chapter 2 Planning and Preparing for System Installation
    1.  2.1 Safety Precautions
    2.  2.2 Items Requiring Confirmation Before Installation
    3. Click 2.3 Confirming the Physical Specifications of the System
    4. Click 2.4 Confirming Rack Specifications
    5. Click 2.5 Checking Environmental Conditions
    6.  2.6 Checking Acoustic Noise Levels
    7.  2.7 Checking Cooling Conditions
    8. Click 2.8 Checking the Power Input Type
    9. Click 2.9 Preparing Power Supply Facilities
    10. Click 2.10 Checking External Interface Port Specifications
    11.  2.11 Checking the Functions of the Operation Panel
  4. Chapter 3 Installing the System
    1.  3.1 Preparing the Necessary Tools/Information for Installation
    2. Click 3.2 Confirming Delivered Components
    3.  3.3 Confirming the Rack
    4. Click 3.4 Mounting the Chassis in a Rack
    5. Click 3.5 Mounting Optional Components
  5. Chapter 4 Connecting Cables to the Chassis
    1.  4.1 Connecting Cables to the SPARC M10-1
    2.  4.2 Connecting Cables to the PCI Expansion Unit
  6. Chapter 5 Performing an Initial System Diagnosis
    1.  5.1 Connecting the System Management Terminal to the Chassis
    2.  5.2 Turning On the Input Power and Starting the XSCF
    3.  5.3 Logging In to the XSCF
    4.  5.4 Checking the XCP Version
    5.  5.5 Checking the Altitude Setting
    6.  5.6 Checking the Time Setting
    7.  5.7 Performing a Diagnosis Test
    8.  5.8 Checking the Component Status
  7. Chapter 6 Making the Initial System Settings
    1.  6.1 Setting the Password Policy
    2.  6.2 Setting a User Account and Password
    3. Click 6.3 Configuring the Telnet/SSH Service
    4.  6.4 Configuring the HTTPS Service
    5. Click 6.5 Configuring the XSCF Network
    6.  6.6 Configuring Memory Mirroring
    7.  6.7 Creating a Physical Partition Configuration List (PCL)
    8.  6.8 Confirming That a System Board (PSB) is Assigned to a Physical Partition (PPAR)
    9.  6.9 Setting a CPU Operational Mode for the Physical Partition
    10.  6.10 Synchronizing the Physical Partition (PPAR) Time and XSCF Time
    11. Click 6.11 Registering a CPU Activation Key
    12.  6.12 Assigning CPU Core Resources to a Physical Partition
    13.  6.13 Starting and Stopping a Physical Partition (PPAR)
    14. Click 6.14 Saving Configuration Information
  8. Appendix A Troubleshooting
    1.  A.1 Understanding the Usual Problems and Their Corrective Actions
    2. Click A.2 Understanding Commands for Troubleshooting
  9. Appendix B Setup Command Workflow
  10. Appendix C Installation Procedure Checklist

2.9.1 Electrical specifications


2.9.1 Electrical specifications
Table 2-8 and Table 2-9 list the electrical specifications of each chassis.
Note - The values listed in Table 2-8 and Table 2-9 are based on values for the maximum configuration of each chassis. The actual values vary depending on the system configuration.
Table 2-8  Electrical specifications (SPARC M10-1)
Item Specification  
  Input voltage of 100 to 120 VAC Input voltage of 200 to 240 VAC
  CPU type:
SPARC64 X		 CPU type:
SPARC64 X+		 CPU type:
SPARC64 X		 CPU type:
SPARC64 X+
Number of power cords 2
(1 for each PSU)		 2
(1 for each PSU)
Power cord length (*1) Maximum length of 3.0 m (9.8 ft.) Maximum length of 3.0 m (9.8 ft.)
Redundancy 1+1 redundant configuration   1+1 redundant configuration  
Frequency
50 Hz/60 Hz, single phase
  
50 Hz/60 Hz, single phase
  
Maximum input current (*2) 8.2 A 8.7 A 4.0 A 4.2 A
Maximum power consumption 806 W 849 W 783 W 824 W
Apparent power
822 VA
866 VA
807 VA
849 VA
Rush current (*3)
40 A peak or less
40 A peak or less
Leakage current (*3) 1.75 mA or less 1.75 mA or less
*1 The SPARC M10-1 is pulled out to perform maintenance. Therefore, you need to consider an extra length of 1.5 m when ordering the power cord.
*2 The current that flows through each power cord in a redundant configuration is half the value listed in Table 2-8.
*3 The value is per power cord.		  
Table 2-9  Electrical specifications (PCI expansion unit)
Item Specification
  Input voltage of 100 to 120 VAC Input voltage of 200 to 240 VAC
Number of power cords
2 (1 for each PSU)
2 (1 for each PSU)
Power cord length Maximum length of 3.0 m (9.8 ft.) Maximum length of 3.0 m (9.8 ft.)
Redundancy 1+1 redundant configuration 1+1 redundant configuration
Frequency
50 Hz/60 Hz, single phase
50 Hz/60 Hz, single phase
Maximum input current (*1) 2.9 A 1.4 A
Maximum power consumption 279 W 270 W
Apparent power
284 VA
276 VA
Rush current (*2)
40 A peak or less
40 A peak or less
Leakage current (*2) 1.75 mA or less 1.75 mA or less
*1 The current that flows through each power cord in a redundant configuration is half the value listed in Table 2-9.
*2 The value is per power cord.

Top of Page