Skip to main content

Contents

  1. Preface
  2. Chapter 1 Understanding the Installation Flow
    1.  1.1 Workflow for the SPARC M10-1
    2. Click 1.2 Workflow for Installing the PCI Expansion Unit
  3. Chapter 2 Planning and Preparing for System Installation
    1.  2.1 Safety Precautions
    2.  2.2 Items Requiring Confirmation Before Installation
    3. Click 2.3 Confirming the Physical Specifications of the System
    4. Click 2.4 Confirming Rack Specifications
    5. Click 2.5 Checking Environmental Conditions
    6.  2.6 Checking Acoustic Noise Levels
    7.  2.7 Checking Cooling Conditions
    8. Click 2.8 Checking the Power Input Type
    9. Click 2.9 Preparing Power Supply Facilities
    10. Click 2.10 Checking External Interface Port Specifications
    11.  2.11 Checking the Functions of the Operation Panel
  4. Chapter 3 Installing the System
    1.  3.1 Preparing the Necessary Tools/Information for Installation
    2. Click 3.2 Confirming Delivered Components
    3.  3.3 Confirming the Rack
    4. Click 3.4 Mounting the Chassis in a Rack
    5. Click 3.5 Mounting Optional Components
  5. Chapter 4 Connecting Cables to the Chassis
    1.  4.1 Connecting Cables to the SPARC M10-1
    2.  4.2 Connecting Cables to the PCI Expansion Unit
  6. Chapter 5 Performing an Initial System Diagnosis
    1.  5.1 Connecting the System Management Terminal to the Chassis
    2.  5.2 Turning On the Input Power and Starting the XSCF
    3.  5.3 Logging In to the XSCF
    4.  5.4 Checking the XCP Version
    5.  5.5 Checking the Altitude Setting
    6.  5.6 Checking the Time Setting
    7.  5.7 Performing a Diagnosis Test
    8.  5.8 Checking the Component Status
  7. Chapter 6 Making the Initial System Settings
    1.  6.1 Setting the Password Policy
    2.  6.2 Setting a User Account and Password
    3. Click 6.3 Configuring the Telnet/SSH Service
    4.  6.4 Configuring the HTTPS Service
    5. Click 6.5 Configuring the XSCF Network
    6.  6.6 Configuring Memory Mirroring
    7.  6.7 Creating a Physical Partition Configuration List (PCL)
    8.  6.8 Confirming That a System Board (PSB) is Assigned to a Physical Partition (PPAR)
    9.  6.9 Setting a CPU Operational Mode for the Physical Partition
    10.  6.10 Synchronizing the Physical Partition (PPAR) Time and XSCF Time
    11. Click 6.11 Registering a CPU Activation Key
    12.  6.12 Assigning CPU Core Resources to a Physical Partition
    13.  6.13 Starting and Stopping a Physical Partition (PPAR)
    14. Click 6.14 Saving Configuration Information
  8. Appendix A Troubleshooting
    1.  A.1 Understanding the Usual Problems and Their Corrective Actions
    2. Click A.2 Understanding Commands for Troubleshooting
  9. Appendix B Setup Command Workflow
  10. Appendix C Installation Procedure Checklist

2.8 Checking the Power Input Type


2.8 Checking the Power Input Type
This section describes the power input types that can be used with the SPARC M10 systems. To prevent serious accidents, confirm that the power supply facilities can supply sufficient redundant power to the system.
In addition, we recommend installing a circuit breaker for each power cord for stable device operation. If multiple power cords are connected to one circuit breaker, multiple power supply units will be affected when the circuit breaker cuts off power.

The server can use the following power input types:
  1. Redundant configuration of power supply units
  2. Dual power feed
  3. Three-phase power feed
  4. Uninterruptible power supply (UPS) connection (optional)
  5. Power distribution unit connection

Top of Page